Dodge 2014 Ram 1500 Owner'S Manual Download Page 280 | Manualshive

Page: 280 / 360

background image

Tow/Haul Mode

To reduce potential for automatic transmission overheat-
ing, activate TOW/HAUL mode when driving in hilly
areas, or select a lower gear range (using the Electronic
Range Select (ERS) shift control) on more severe grades.

Electronic Speed Control — If Equipped

•

Do not use in hilly terrain or with heavy loads.

•

When using the speed control, if you experience speed
drops greater than 10 mph (16 km/h), disengage until
you can get back to cruising speed.

•

Use speed control in flat terrain and with light loads to
maximize fuel efficiency.

Cooling System

To reduce potential for engine and transmission over-
heating, take the following actions:

City Driving

When stopped for short periods of time, shift the trans-
mission into NEUTRAL and increase engine idle speed.

Highway Driving

Reduce speed.

Air Conditioning

Turn off temporarily.

278

STARTING AND OPERATING

«
...
278
279
280
281
282
...
»

Summary of Contents for 2014 Ram 1500









































































































































































































































































































































































Reviews:

No comments

Related manuals for 2014 Ram 1500

Brand: ZAPTEC Pages: 64

Brand: ZAPTEC Pages: 24

Brand: Samsung Pages: 133

Brand: Ultra-tow Pages: 14

Brand: Mercedes-Benz Pages: 121

Brand: Menabo Pages: 8

Brand: Camtree Pages: 5

Brand: Metra Electronics Pages: 20

Brand: HAUL MASTER Pages: 8

Brand: Mercedes-Benz Pages: 358

Tata Indigo Diesel

Brand: TATA Motors Pages: 190

Prime Design HBR-E-FT33B

Brand: Safe Fleet Pages: 12

Brand: Xhorse Pages: 48

Brand: Skoda Pages: 281

Brand: FALCON RIDGE Pages: 4

Brand: Black+Decker Pages: 21

Brand: Beeper Pages: 20

Brand: Fiat Pages: 284

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands