Dodge 2014 Ram 1500 Owner'S Manual Download Page 243 | Manualshive

Page: 243 / 360

background image

Fully press the clutch pedal before shifting gears. As you
release the clutch pedal, lightly press the accelerator
pedal.

This transmission has a “creeper” first gear which should
be used to start from a standing position when carrying a
payload or towing a trailer. Damage to the clutch can
result from starting in second or third gear with a loaded
vehicle. An unloaded vehicle may be launched in second
gear. Use each gear in numerical order – do not skip a gear.

NOTE:

When loaded, pulling a trailer or on a grade, the

truck should always start in first gear and not skip gears.

Recommended Vehicle Shift Speeds

To utilize your manual transmission efficiently for both
fuel economy and performance, it should be upshifted as
listed in recommended shift speed chart. Shift at the
vehicle speeds listed for acceleration. When heavily
loaded or pulling a trailer these recommended up-shift
speeds may not apply.

Maximum Recommended Up-Shift Speeds

Gear Selection

1 to 2

2 to 3

3 to 4

4 to 5

5 to 6

Maximum

Speed

7 mph

(11 km/h)

15 mph

(24 km/h)

25 mph

(40 km/h)

40 mph

(64 km/h)

45 mph

(72 km/h)

4

STARTING AND OPERATING

241

«
...
241
242
243
244
245
...
»

Summary of Contents for 2014 Ram 1500









































































































































































































































































































































































Reviews:

No comments

Related manuals for 2014 Ram 1500

Brand: Wallbox Pages: 7

Reference Series

Brand: OEM Audio Pages: 29

Brand: Suzuki Pages: 353

Brand: Torklift Pages: 16

Brand: Icom Pages: 20

Brand: Skoda Pages: 165

Brand: EUFAB Pages: 12

Brand: Aries Pages: 5

Brand: Mercedes-Benz Pages: 354

Brand: Tesla Pages: 274

Brand: Prorack Pages: 15

Grand Cherokee SRT 2019

Brand: Jeep Pages: 656

Brand: PUTCO Pages: 3

Brand: Aries Pages: 3

Camry Hybrid 2012

Brand: Toyota Pages: 62

Brand: Wabtec Pages: 216

Brand: OEM Audio Pages: 21

Brand: Paser Pages: 10

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands