Dodge 2014 Ram 1500 Owner'S Manual Download Page 111 | Manualshive

Page: 111 / 360

background image

3. Open the water drain valve, and let any accumulated

water drain.

4. Close the water drain valve.

5. Remove bottom cover using a strap wrench. Rotate

counterclockwise for removal. Remove the used o-ring
and discard it.

6. Remove the used filter cartridge from the housing and

dispose of it according to your local regulations.

7. Wipe the sealing surfaces of the lid and housing clean.

8. Install a new o-ring into the ring groove on the filter

housing and lubricate with clean engine oil.

NOTE:

WIF (Water In Fuel) sensor is re-usable. Service

kit comes with new o-ring for filter canister and WIF
sensor.

Priming If The Engine Has Run Out Of Fuel

WARNING!

Do not open the high pressure fuel system with the
engine running. Engine operation causes high fuel
pressure. High pressure fuel spray can cause serious
injury or death.

1. Add a substantial amount of fuel to the tank, approxi-

mately 2 to 5 gal (8L to 19L).

2. Press ignition switch twice without your foot on brake

to put vehicle in Run position. This will activate the in
tank fuel pump for approximately 30 seconds. Repeat
this process twice.

3. Start the engine using the “Normal Starting” proce-

dure. Refer to “Starting Procedures” in “Starting and
Operating” for further information.

5

MAINTAINING YOUR VEHICLE

109

«
...
109
110
111
112
113
...
»

Summary of Contents for 2014 Ram 1500









































































































































































































































































































































































Reviews:

No comments

Related manuals for 2014 Ram 1500

Brand: iDataLink Pages: 30

Brand: Carefree Pages: 12

Brand: Aries Pages: 3

Brand: GOgroove Pages: 9

3-series convertible

Brand: BMW Pages: 98

Brand: Wagan Pages: 8

Brand: Thermo King Pages: 2

Brand: tams elektronik Pages: 44

MultiCharger 1204

Brand: DEFA Pages: 28

Brand: Steelmate Pages: 14

Brand: Arrista Pages: 2

Brand: Suzuki Pages: 504

Brand: Buick Pages: 112

Brand: ICON Pages: 4

Brand: Ranger design Pages: 14

Brand: Hama Pages: 2

Brand: Edelbrock Pages: 2

V-520 RT Series

Brand: Thermo King Pages: 56

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands