Dodge 2014 Ram 1500 Owner'S Manual Download | Manualshive

Page: 148 / 360

background image

REMOTE STARTING SYSTEM — IF EQUIPPED

This system uses the Remote Keyless Entry
(RKE) transmitter to start the engine conve-
niently from outside the vehicle while still
maintaining security. The system has a range of

approximately 300 ft (91 m).

NOTE:

•

The vehicle must be equipped with an automatic
transmission to be equipped with Remote Start.

•

The remote start system will wait for the “Wait To
Start” telltale to extinguish before cranking the engine.
This allows time for the intake heater to pre-heat the
incoming air, and is normal operation in cold weather.
Refer to “Electronic Vehicle Information Center/EVIC

Warning Lights” in “Understanding Your Instrument
Panel” for further information on and “Wait To Start”
telltale and pre-heat cycle.

How To Use Remote Start

All of the following conditions must be met before the
engine will remote start:

•

Shift lever in PARK

•

Doors closed

•

Hood closed

•

HAZARD switch off

•

BRAKE switch inactive (brake pedal not pressed)

•

Ignition key removed from ignition switch

•

Battery at an acceptable charge level

•

RKE PANIC button not pressed

146

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

«
...
146
147
148
149
150
...
»

Summary of Contents for 2014 Ram 1500









































































































































































































































































































































































Reviews:

No comments

Related manuals for 2014 Ram 1500

Brand: Dakota Digital Pages: 2

Brand: Dakota Digital Pages: 7

Sprinter Bed System Adventure Wagon Kit

Brand: FVC Pages: 8

Brand: Whispbar Pages: 77

Brand: Honda Pages: 208

Brand: EUFAB Pages: 52

Brand: Hyundai Pages: 18

Brand: EUFAB Pages: 16

Brand: RBO Pages: 15

Brand: Jaeger Pages: 13

Brand: Mercedes-Benz Pages: 10

Brand: Mitsubishi Pages: 362

Brand: Cadillac Pages: 335

Brand: Buick Pages: 371

Brand: Brodit Pages: 2

spectroFlex Car Adapter

Brand: wtw Pages: 4

EQ forfour 2018

Brand: SMART Pages: 224

MagicWatch MWE850

Brand: Waeco Pages: 200

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands