background image

Features

High Performance, Low Power 32-bit Atmel

®

 AVR

®

 Microcontroller

– Compact Single-Cycle RISC Instruction Set Including DSP Instruction Set

– Read-Modify-Write Instructions and Atomic Bit Manipulation

– Performing up to 1.51DMIPS/MHz

• Up to 126 DMIPS Running at 84MHz from Flash (1 Wait-State)

• Up to 63 DMIPS Running at 42MHz from Flash (0 Wait-State)

– Memory Protection Unit

Multi-Layer Bus System

– High-Performance Data Transfers on Separate Buses for Increased Performance

– 8 Peripheral DMA Channels (PDCA) Improves Speed for Peripheral 

Communication

– 4 generic DMA Channels for High Bandwidth Data Paths

Internal High-Speed Flash

– 256KBytes, 128KBytes, 64KBytes versions

– Single-Cycle Flash Access up to 36MHz 

– Prefetch Buffer Optimizing Instruction Execution at Maximum Speed

– 4 ms Page Programming Time and 8ms Full-Chip Erase Time

– 100,000 Write Cycles, 15-year Data Retention Capability

– Flash Security Locks and User Defined Configuration Area

Internal High-Speed SRAM

– 64KBytes Single-Cycle Access at Full Speed, Connected to CPU Local Bus

– 64KBytes (2x32KBytes with independent access) on the Multi-Layer Bus System

Interrupt Controller

– Autovectored Low Latency Interrupt Service with Programmable Priority

System Functions

– Power and Clock Manager Including Internal RC Clock and One 32KHz Oscillator

– Two Multipurpose Oscillators and Two Phase-Lock-Loop (PLL), 

– Watchdog Timer, Real-Time Clock Timer

External Memories

– Support SDRAM, SRAM, NandFlash (1-bit and 4-bit ECC), Compact Flash

– Up to 66 MHz

External Storage device support

– MultiMediaCard (MMC V4.3), Secure-Digital (SD V2.0), SDIO V1.1

– CE-ATA V1.1, FastSD, SmartMedia, Compact Flash

– Memory Stick: Standard Format V1.40, PRO Format V1.00, Micro

– IDE Interface

One Advanced Encryption System (AES) for AT32UC3A3256S, AT32UC3A3128S, 

AT32UC3A364S, AT32UC3A4256S, AT32UC3A4128S and AT32UC3A364S

– 256-, 192-, 128-bit Key Algorithm, Compliant with FIPS PUB 197 Specifications

– Buffer Encryption/Decryption Capabilities

Universal Serial Bus (USB)

– High-Speed USB 2.0 (480Mbit/s) Device and Embedded Host

– Flexible End-Point Configuration and Management with Dedicated DMA Channels

– On-Chip Transceivers Including Pull-Ups

One 8-channel 10-bit Analog-To-Digital Converter, multiplexed with Digital IOs.

Two Three-Channel 16-bit Timer/Counter (TC)

Four Universal Synchronous/Asynchronous Receiver/Transmitters (USART) 

– Fractionnal Baudrate Generator

32-bit AVR 
Microcontroller

AT32UC3A3256S
AT32UC3A3256
AT32UC3A3128S
AT32UC3A3128
AT32UC3A364S
AT32UC3A364
AT32UC3A4256S
AT32UC3A4256
AT32UC3A4128S
AT32UC3A4128
AT32UC3A464S
AT32UC3A464

32072H-AVR32–10/2012

Summary of Contents for AT32UC3A3128






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews: