Altigen ACM 6.7 Administrator'S Manual Download Page 396

Page: 396 / 470

Additional Steps for Bridged Access and Native VM Integration

382

MAXCS ACM 6.7 Administration Manual

1. In

Recipient Configuration > Mailbox

, select the user and select

Enable Unified

Messaging

from the Actions pane.

Figure 169. Here, Leslie Xia is an individual IP phone user with a mailbox in VMDOMAIN.

2. Click

Browse

and select the policy that is associated with the dialing plan you just

created, then click

Figure 170. The policy associated with the dialing plan we just created is “LeslieXiaSS

Default Policy”.

3. Enter the user’s MAXCS extension number in the

Manually entered mailbox

extension

field (make sure the extension number is the same in MaxAdmin and the

Exchange User Mailbox).

Summary of Contents for ACM 6.7























































































































































































































































































































































































































































































Search results

Summary of Contents for ACM 6.7

Reviews:

Related manuals for ACM 6.7

Brands by name

Popular brands

Altigen ACM 6.7, Administrator'S Manual

Search results

Summary of Contents for ACM 6.7

Reviews:

Related manuals for ACM 6.7

Brands by name

Popular brands