Altigen ACM 6.7 Administrator'S Manual Download Page 39 | Manualshive

Page: 39 / 470

background image

System Requirements and Installation

MAXCS ACM 6.7 Administration Manual 25

•

Triton Resource Board Rev A3 or above

•

Triton MeetMe Conference board all revisions

•

Triton 0x12 Rev. B (Whitney III) all revisions

•

Proton Analog 12-Trunk Board all revisions

•

MAX 1000 and MAX2000 hardware boards:

•

0x12 analog extension board

•

4x8 analog board

•

8x4 analog board

•

T1 4x4 combo board

•

T1 board

Boards supported in ACC and ACM

•

Gateway only board: Dual T1/E1/PRI with 60 IP (G.711 only) resources

MAXCS Licenses

In MAXCS 6.7, most client licenses are available in both concurrent session mode and
seat-based mode. Both types can be mixed in a MAXCS system.
The following licenses are available for

all AltiGen 6.7 systems

:

Licenses for 6.7

MAXCS ACM

Per system

MAXCS ACC

Per system

MaxCommunicator

Per seat or per session

AltiConsole

Per session

MaxAgent

Per seat or per session

MaxSupervisor

Per seat or per session

IPTalk

Per seat or per session

MaxCall

Per seat or per session

TAPI

Per extension configuration

SIP Trunk

Per activated SIP trunk

3rd Party SIP Device

Per seat registering as an IP extension (non-concurrent)

Enterprise Manager

Per server license

Dedicated Recording Seat
License

Per seat assigned to record to a centralized folder, and
per trunk port with recording enabled

Concurrent Recording Session
License

Per session

MaxMobile

Per seat

Multilingual

Per system

Advanced Call Router

Per system

AltiReport

Per system

VRManager

Per system

MaxInSight

Per session

SDK Connection Session

Per session

«
...
37
38
39
40
41
...
»

Summary of Contents for ACM 6.7























































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ACM 6.7

MME239 - Micro DVD Home Theater System

Brand: Magnavox Pages: 41

Brand: Rane Pages: 14

Brand: WaterCop Pages: 4

Brand: Tokai Pages: 20

Brand: Clarion Pages: 83

Brand: Hioki Pages: 52

AUDEMAT FM PROBE

Brand: Worldcast Systems Pages: 80

Stealthbox SB-GM-4GSUVCNSL/10TW1

Brand: JL Audio Pages: 7

Brand: AudioBahn Pages: 13

Brand: Xonax Pages: 24

Brand: Philips Pages: 2

Brand: Philips Pages: 2

Brand: Philips Pages: 22

Brand: Philips Pages: 26

Brand: Philips Pages: 28

Brand: Philips Pages: 86

Brand: Sony Pages: 60

Brand: Sony Pages: 70

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands