Altigen ACM 6.7 Administrator'S Manual Download Page 235

Page: 235 / 470

MAXCS ACM 6.7 Administration Manual 221

H A P T E R

AltiGen IP Phone Configuration

AltiGen manufactures a series of IP phones. The system administrator can control and
program the following areas for each type of AltiGen IP phone:

•

Specify the server IP address that the IP phone needs to register

•

Protect the IP phone configuration with a password

•

Prevent the user from changing the configuration from the IP phone

•

Configure the Trunk Access (Route Access) code

•

Configure the time zone and time format

•

Specify the TFTP server for firmware updates

•

Force the IP phone to reset and download new firmware

•

Set SIP transport settings for SIP security

•

Enable SIP telephony service for a selected third-party SIP device

•

Configure programmable keys

•

Allow the IP phone to receive workgroup real time status

•

Allow the phone to auto-discover the server’s IP address

Configuring the AltiGen IP Phone

To configure the AltiGen IP phone, select

PBX > AltiGen IP Phone Configuration

This opens the

AltiGen IP Phone Configuration

window, where, after setting up an IP

extension, you can set parameters for the extension:

Summary of Contents for ACM 6.7























































































































































































































































































































































































































































































Search results

Summary of Contents for ACM 6.7

Reviews:

Related manuals for ACM 6.7

Brands by name

Popular brands

Altigen ACM 6.7, Administrator'S Manual

Search results

Summary of Contents for ACM 6.7

Reviews:

Related manuals for ACM 6.7

Brands by name

Popular brands