Altigen ACM 6.7 Administrator'S Manual Download Page 381 | Manualshive

Page: 381 / 470

background image

MAXCS ACM 6.7 Administration Manual 367

C

H A P T E R

27

System Report Management

MAXCS provides a System Summary report, an IP Cumulative Traffic Statistics report,
and an SNMP (Simple Network Management Protocol) configuration screen, all available
from the

Report

menu.

System Summary Report

The System Summary report provides summary information on extensions, trunks, and
workgroups configured in the system. To open the System Summary report window,
select

Report

>

System Summary

, or click the

Summary

button on the toolbar.

Figure 155. System Summary window

The system summary report displays:

«
...
379
380
381
382
383
...
»

Summary of Contents for ACM 6.7























































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ACM 6.7

Brand: cinetto Pages: 56

Brand: Lincoln Electric Pages: 2

Brand: SIMARINE Pages: 22

Brand: Taiden Pages: 19

TorqueTrak Revolution

Brand: Binsfeld Pages: 2

Brand: Signal Pages: 16

AUDIO SYSTEM CONTROLLER SC-1

Brand: Wisdom Pages: 52

Brand: Bogen Pages: 13

Brand: Contacta Pages: 12

Brand: Yamaha Pages: 48

Brand: Yamaha Pages: 51

Brand: Yamaha Pages: 138

Brand: Philips Pages: 1

Brand: Philips Pages: 1

Brand: Philips Pages: 2

Brand: Philips Pages: 19

Brand: Philips Pages: 20

Brand: Philips Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands