Altigen ACM 6.7 Administrator'S Manual Download Page 305

Page: 305 / 470

Queue Management - Advanced

MAXCS ACM 6.7 Administration Manual 291

Figure 136. Workgroup Configuration, Queue Management, Advanced Queue Control

To configure options for advanced queuing control, click the

Setup

button. This opens

the Advanced Queue Management (AQM) application configuration window with tabs for
configuring

Announcement

Menu Selection

, and

Queue Overflow

Announcement

The

Announcement

tab allows for configuration of queue announcements.

Figure 137. Workgroup Configuration, Advanced Queue Management, Announcement tab

To configure queue announcements:
1. Select any of the following check boxes:

•

Use

Default

System

Phrases

•

Queue

Position

Summary of Contents for ACM 6.7























































































































































































































































































































































































































































































Search results

Summary of Contents for ACM 6.7

Reviews:

Related manuals for ACM 6.7

Brands by name

Popular brands

Altigen ACM 6.7, Administrator'S Manual

Search results

Summary of Contents for ACM 6.7

Reviews:

Related manuals for ACM 6.7

Brands by name

Popular brands