Altigen ACM 6.7 Administrator'S Manual Download Page 421 | Manualshive

Page: 421 / 470

background image

Trace Collector

MAXCS ACM 6.7 Administration Manual 407

To shut down all AltiGen services, click the

Shutdown All AltiGen Services

button.

Some examples of when you might want to do this are before you upgrade, before
running some utilities and tools, and to apply certain configuration changes.
To start all AltiGen services, click the

Start All AltiGen Services

button.

Trace Collector

The Trace Collector is for use by experienced technicians. It collects trace for diagnostic
purposes, and lets you upload the results to AltiGen Technical Support right from the
Trace Collector dialog box. Technicians can run the Trace Collector tool from the
Windows

Start

menu, and also from MaxAdmin’s

Diagnostic

menu. Log in with the

super technician password "jazzy" and then the current password when logging into
MaxAdmin. This enables the diagnostic menu options.

Note:

Trace Collector is not available from an MaxAdmin installed in a remote machine.

The Trace Collector first examines the running status of MAXCS and the gateway, and
then checks whether each trace status is on or off. If a trace status is turned off, the
AltiGen system will not produce those traces. A message box pops up if MAXCS and the
gateway are not running or an important trace status is off.

«
...
419
420
421
422
423
...
»

Summary of Contents for ACM 6.7























































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ACM 6.7

Brand: Zenith Pages: 14

Brand: Panasonic Pages: 2

RXD15 - RADIO CASSETTE W/CD

Brand: Panasonic Pages: 8

Brand: Lars Thrane Pages: 141

Brand: Teac Pages: 2

Brand: Absima Pages: 5

Brand: Aeta Audio Systems Pages: 24

Brand: HEIDENHAIN Pages: 32

Brand: ICT Pages: 11

SAM GENERATION 2

Brand: HALE Pages: 12

Brand: HK Audio Pages: 105

Brand: vistaCNC Pages: 7

Brand: Blaupunkt Pages: 8

Brand: Raven Pages: 48

Brand: Aqua Control Pages: 16

Brand: LG Pages: 20

Brand: LG Pages: 36

Brand: LG Pages: 20

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands