Altigen ACM 6.7 Administrator'S Manual Download Page 278

Page: 278 / 470

Workgroup Functionalities

264

MAXCS ACM 6.7 Administration Manual

•

Agent ready/not-ready and wrap-up management

•

Record inbound and outbound workgroup calls

•

Allow supervisor to redirect call

•

Allow supervisor to change call priority in queue (MAXCS ACM)

•

Define workgroup operation hours and routing (MAXCS ACM)

•

Auto logout all agents after operation hours (MAXCS ACM)

•

Priority queuing and call distribution (MAXCS ACM)

•

Skill-based routing (MAXCS ACM)

•

Caller selectable information menu while in queue (MAXCS ACM)

Agent’s Phone Operation

•

Set Login (#54) and Logout (#56)

•

Set Ready (#90) and Not Ready (#91)

•

Set outbound WG number (#53)

Agent Desktop Application (MaxAgent)

•

Real-time workgroup queue and agent statistics display

•

Ability to view and check workgroup voice mail

•

Set Login and Logout

•

Set Ready and Not Ready

•

View and pick up calls in queue

•

Calls in queue alert option

•

Daily performance summary

•

View other agents’ status

•

View caller’s IVR data and User Data

•

Tag memo to a call

Supervisor’s Phone Operation

•

Listen to agent’s conversation with feature code

#59

Supervisor’s Desktop Application (MaxSupervisor)

•

View agent’s state

•

Record agent’s conversation

•

Manage agent’s login/logout status

•

Listen, barge in, or coach agent’s conversation

•

View agent’s daily performance statistics

•

View group’s real-time status

•

View group’s daily operation result

•

View calls in queue

•

Be alerted to calls in queue

•

Change call priority (MAXCS ACM)

Summary of Contents for ACM 6.7























































































































































































































































































































































































































































































Search results

Summary of Contents for ACM 6.7

Reviews:

Related manuals for ACM 6.7

Brands by name

Popular brands

Altigen ACM 6.7, Administrator'S Manual

Search results

Summary of Contents for ACM 6.7

Reviews:

Related manuals for ACM 6.7

Brands by name

Popular brands