Altigen ACM 6.7 Administrator'S Manual Download Page 372

Page: 372 / 470

Configuring the NICs

358

MAXCS ACM 6.7 Administration Manual

3. Enter an IP address and subnet for the NIC. When configuring the second NIC on the

Softswitch, use

the same subnet

4. For the sharing NIC, set the

Default gateway

For the redundancy control NIC, leave the

Default gateway

field

empty

5. Click the

Advanced

button, and make sure

Automatic Metric

is checked. Click

6. Go to

Control Panel > Network Connections

. From the menu, select

Advanced

> Advanced Settings

. Move the shared NIC to be the first one in the Connections

panel.

Summary of Contents for ACM 6.7























































































































































































































































































































































































































































































Search results

Summary of Contents for ACM 6.7

Reviews:

Related manuals for ACM 6.7

Brands by name

Popular brands

Altigen ACM 6.7, Administrator'S Manual

Search results

Summary of Contents for ACM 6.7

Reviews:

Related manuals for ACM 6.7

Brands by name

Popular brands