Altigen ACM 6.7 Administrator'S Manual Download Page 173 | Manualshive

Page: 173 / 470

background image

Configuring Virtual Board HMCP

MAXCS ACM 6.7 Administration Manual 159

2. Play and Record Voice Files

•

Announce system and queue phrases

•

Process auto attendant

•

Process voice mail

•

Call recording for IP extensions

3. Provide Conferencing Resources

•

Station conference

•

Meet-Me conference

•

Barge-in/silent monitor/coaching

From a deployment point of view, an HMCP media server can be installed in the same
Softswitch system sharing the same CPU or can be in a stand-alone server with a
dedicated CPU.

Notes

:

•

Do not install HMCP service in a system with AltiGen's Triton telephony board. It will
cause resource conflict.

•

Remove the Triton Resource board and MeetMe conference board from OFFICE
systems running as a gateway. Station conference, MeetMe conference, and barge-
in/silent monitor/coaching will use HMCP voice processing resources when deploying
Multi-Gateway Softswitch.

•

An HMCP Media Server license is required to activate an HMCP virtual board.

By default the system grants 60 conference members in a maximum of 40 bridges. You
can change the number to as many as 120 members in a maximum of 40 bridges, and
you can activate other HMCP resources, by double-clicking an HMCP board in Boards
view and then clicking the Board Configuration button to open this dialog box:

«
...
171
172
173
174
175
...
»

Summary of Contents for ACM 6.7























































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ACM 6.7

Brand: DayTronic Pages: 414

Brand: LaserBit Pages: 69

Brand: Purelogic Pages: 60

Brand: Fagor Pages: 68

Brand: ZheJiang Libiao Robotics Pages: 10

Brand: Daewoo Pages: 22

SmartStuff SmartBox

Brand: TCP Pages: 2

DMU380SA Series

Brand: Memsic Pages: 105

Brand: Taiden Pages: 19

Brand: Grundig Pages: 28

Brand: Zenith Pages: 20

Brand: B&O Play Pages: 52

Brand: AbleNet Pages: 8

Brand: GE Pages: 96

Brand: Boss Audio Systems Pages: 6

Brand: Boss Audio Systems Pages: 25

Brand: NEC Pages: 1098

Brand: AMX Pages: 58

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands