manualshive.com logo in svg

Altigen ACM 6.7, Administrator'S Manual

The Altigen ACM 6.7, a sophisticated communication management system, offers seamless integration of various channels. To maximize user experience, an Administrator's Manual is available for free download at manualshive.com. This comprehensive manual empowers users with detailed instructions and insights, ensuring efficient utilization of the product's diverse features and functionalities.

Share
Download
background image

Configuration Guidelines for NAT

310

  MAXCS ACM 6.7 Administration Manual

•

A switch is required; VoIP quality can be adversely affected if a hub is used.

Configuration Guidelines for NAT

Note:

This section only applies to AltiGen IP phones or IPTalk integrated with 
MaxCommunicator or MaxAgent. 

The section discusses the configuration guidelines when MAXCS is behind NAT (Network 
Address Translation) and communication to AltiGen IP phones, IPTalk, or another MAXCS 
is over WAN. AltiGen SIP phones support NAT traversal, which does not require special 
settings on the NAT router at the remote site.
Due to H.323/SIP protocol, which puts the IP address information in the TCP/IP payload, 
the NAT router requires some H.323 protocol and SIP protocol implementation to 
correctly handle the H.323/SIP traffic and translate the private IP address into a public 
IP address. Not all NAT routers have this kind of implementation. If the NAT router does 
not support H.323/SIP,

 

you need to check 

Enable SIP NAT support

 and 

Enable H323 

NAT support

 in Enterprise Manager, 

IP Networks

 tab. 

The following sections illustrate a private network configuration and a VPN configuration. 
For information on setting up VoIP traffic forwarding for NAT and configuring MAXCS 
behind NAT, see “Configuring MAXCS Behind NAT” on page 327.

Private Network Configuration Example

(MAXCS with private IP address and behind NAT)
Only the private IP address is used in a private network—the public router will not route 
the packet that has a private IP address as its destination. (All IP addresses beginning 
with 192.168.x.x, 10.x.x.x, or 172.16.x.x to 172.32.x.x are private IP addresses.)

Summary of Contents for ACM 6.7























































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ACM 6.7

Magnavox MAS-80 Manual Del Usuario preview
MAS-80
Brand: Magnavox Pages: 23
Yamaha PJP-EC200 Setup Procedure preview
PJP-EC200
Brand: Yamaha Pages: 14
Yamaha PJP-50R Basic Operation Manual preview
PJP-50R
Brand: Yamaha Pages: 28
Yamaha CS-700 Series Operation Manual preview
CS-700 Series
Brand: Yamaha Pages: 109
Yamaha PJP-100UH Additional Information preview
PJP-100UH
Brand: Yamaha Pages: 3
Absima CR9T Quick Start preview
CR9T
Brand: Absima Pages: 5
Brähler Systems 05.0055 Instruction Manual preview
05.0055
Brand: Brähler Systems Pages: 25
MPMan DAB320 (German) Manual preview
DAB320
Brand: MPMan Pages: 32
Ruida Technology LFS-PM Series Operating Manual preview
LFS-PM Series
Brand: Ruida Technology Pages: 35
Saltillo NOVA chat 5 Quick Reference Manual preview
NOVA chat 5
Brand: Saltillo Pages: 2
ALLEN & HEATH dLive CDM32 Getting Started User Manual preview
dLive CDM32
Brand: ALLEN & HEATH Pages: 14
Aiphone NHX SYSTEM series Operation Manual preview
NHX SYSTEM series
Brand: Aiphone Pages: 12
Edis 020017-1 User Manual preview
020017-1
Brand: Edis Pages: 39
Brahler CDSVAN Operating Instructions Manual preview
CDSVAN
Brand: Brahler Pages: 32
RADICAL R-C11H Y1 Device Installation Manual preview
R-C11H Y1
Brand: RADICAL Pages: 18
BTG EKOS Instructions For Use Manual preview
EKOS
Brand: BTG Pages: 71
Nagra CLASSIC PHONO User Manual preview
CLASSIC PHONO
Brand: Nagra Pages: 22
Yamaha YDSP-1 Owner'S Manual preview
YDSP-1
Brand: Yamaha Pages: 48

Brands by name

Popular brands

Load more brands