Altigen ACM 6.7 Administrator'S Manual Download Page 130 | Manualshive

Page: 130 / 470

background image

Opening the Trunk Configuration Window

116

MAXCS ACM 6.7 Administration Manual

Figure 54. Channel Information box

Opening the Trunk Configuration Window

To open the general

Trunk Configuration

window, do one of the following:

•

Click the

Trunk Configuration

button

in the toolbar.

•

Select

PBX > Trunk Configuration

.

•

Double-click a trunk in the

Trunk View

window.

Figure 55. Trunk View window

Selecting Channel
Properties from the
right-click menu in
Trunk View bypasses
the general Trunk
Configuration window
to open a trunk
properties window
specific to the selected
trunk.

«
...
128
129
130
131
132
...
»

Summary of Contents for ACM 6.7























































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ACM 6.7

Brand: Sven Pages: 12

Brand: cinetto Pages: 56

Brand: DAPAudio Pages: 12

Brand: WesAudio Pages: 65

ADAP-KOOL AK-SM 800

Brand: Danfoss Pages: 4

Brand: VIS-A-VIS Pages: 4

Brand: Mircom Pages: 149

Brand: Panasonic Pages: 20

Brand: Panasonic Pages: 20

Brand: Panasonic Pages: 20

Brand: Panasonic Pages: 116

Brand: Panasonic Pages: 20

Brand: btsr Pages: 45

Brand: Extron electronics Pages: 2

Brand: MAC Audio Pages: 2

EtherNet/IP E84DGFCGEJP

Brand: Lenze Pages: 149

Brand: Raven Pages: 104

Brand: Sharp Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands