Altigen ACM 6.7 Administrator'S Manual Download Page 41 | Manualshive

Page: 41 / 470

background image

System Requirements and Installation

MAXCS ACM 6.7 Administration Manual 27

•

You cannot use both a hardware device and the soft system key at the same
time.

•

When using a soft system key, the MaxCS system must be a member of an
Active Directory domain.

•

Software license key

—A 20-digit key located on the front of the End User License

Agreement.

Installing MAX Communication Server

To install MAXCS, insert the MAXCS CD ROM into the CD ROM drive of the server, and
follow the instructions on the install screens. At the third screen, select a setup type:

•

All-in-one (Stand Alone) System Installation

—Select this option if MAXCS ACC

will be operating on a single server. (This is the most common installation option.)

•

Multi-Gateway Softswitch System Installation

—Select this option if the

Softswitch, Media Server, and gateway(s) will be running in different chassis in an
enterprise deployment. On the next screen you can select which components to
install.

•

Redundant System Installation

—Select this option if you are setting up a

redundant system. On the next screen you can select the components to install.

Multi-Gateway Softswitch System Installation

These are the components you have to choose from.

«
...
39
40
41
42
43
...
»

Summary of Contents for ACM 6.7























































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ACM 6.7

Brand: Panasonic Pages: 2

Brand: Panasonic Pages: 6

Brand: Panasonic Pages: 142

Brand: Panasonic Pages: 68

Brand: Panasonic Pages: 68

Brand: Xtrons Pages: 11

Brand: Harman Pages: 10

AZ8350 - Cd Radio Cass Recorder

Brand: Magnavox Pages: 18

Brand: Panasonic Pages: 4

Brand: V2 Pages: 48

Brand: KanDao Pages: 265

Brand: S.E.M. Pages: 6

Brand: Tokai Pages: 20

Brand: V-ZUG Pages: 24

iAqualink IQ904-P

Brand: Zodiac Pages: 2

Brand: H2flow Pages: 16

Brand: Vaillant Pages: 56

Brand: Valcom Pages: 6

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands