Altigen ACM 6.7 Administrator'S Manual Download Page 394

Page: 394 / 470

Additional Steps for Bridged Access and Native VM Integration

380

MAXCS ACM 6.7 Administration Manual

Figure 167. The name of our example gateway is “LeslieXia” and the name of the dial

plan we created is “LeslieXiaSS”.

a. Enter the name of the gateway.
b. Enter the IP address of your MAXCS server.
c.

Browse for and select the dial plan you just created.

d. Click

New

6. If your system has multiple gateways, repeat step 5 to add all of your gateways as

UM IP Gateways.

7. Associate your dial plan to the Exchange Server UM. To do this, in the Exchange

Management Console, go to

Server Configuration > Unified Messaging

, select

the server and click

Properties

Summary of Contents for ACM 6.7























































































































































































































































































































































































































































































Search results

Summary of Contents for ACM 6.7

Reviews:

Related manuals for ACM 6.7

Brands by name

Popular brands

Altigen ACM 6.7, Administrator'S Manual

Search results

Summary of Contents for ACM 6.7

Reviews:

Related manuals for ACM 6.7

Brands by name

Popular brands