Altigen ACM 6.7 Administrator'S Manual Download Page 86 | Manualshive

Page: 86 / 470

background image

Managing Gateways

72

MAXCS ACM 6.7 Administration Manual

Figure 27. Multi-Gateway Softswitch deployment using OFFICE3G server

Note:

MAXCS and gateway servers have to be on the same LAN. Connecting a gateway
from a remote site to the MAXCS site through a WAN connection is not supported.
The WAN network delay and latency may cause synchronization signal failure
between MAXCS and the gateway.

Note:

An AltiGen Gateway license is required to set up a gateway.

Managing Gateways

Whether you are using multiple gateways or one gateway, you will perform gateway
management functions in the Softswitch Component Configuration window.
The Softswitch Component Configuration window lists each gateway in your system, its
ID, name, and type (media server or gateway), status, IP address, password, country,
and how many IP phones are assigned to the gateway as a home gateway. Use this
window to:

•

Add and delete a gateway

•

Attach and detach a gateway

•

Change a gateway name, IP address, password, country

•

Enable Media Server on the Softswitch

•

Set TDM Bus mode for a gateway

•

Set CT-Bus clock for a gateway

To open the Softswitch Component Configuration window, select

System >

Softswitch

Component Management

.

«
...
84
85
86
87
88
...
»

Summary of Contents for ACM 6.7























































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ACM 6.7

Brand: hotset Pages: 2

Brand: ION Pages: 48

Brand: Parklio Pages: 12

Brand: NAIM Pages: 31

Brand: VAT Pages: 53

DE-3000+ Series

Brand: Altronic Pages: 77

Brand: aija audio Pages: 4

Brand: Jacuzzi Pages: 28

Brand: Forge Electronics Pages: 10

Brand: Alpine Pages: 19

Alltech 3300 ELSD

Brand: DataApex Pages: 20

Brand: Kenwood Pages: 26

Brand: Kenwood Pages: 32

Brand: Kenwood Pages: 17

Brand: Kenwood Pages: 20

Brand: Kenwood Pages: 52

Brand: Kenwood Pages: 34

Brand: Kenwood Pages: 30

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands