manualshive.com logo in svg

Altigen ACM 6.7, Administrator'S Manual

The Altigen ACM 6.7, a sophisticated communication management system, offers seamless integration of various channels. To maximize user experience, an Administrator's Manual is available for free download at manualshive.com. This comprehensive manual empowers users with detailed instructions and insights, ensuring efficient utilization of the product's diverse features and functionalities.

Share
Download
background image

MAXCS ACM 6.7 Administration Manual  115

11

Trunk Configuration

Trunk attributes and parameters are set using the 

Trunk Configuration

 window. The 

attributes and options available depend on the type of board and trunk. This chapter 
discusses general configuration options applicable to all trunks, followed by specific 
configuration options for the following trunk types:

•

H.323 tie trunk, page 121

•

SIP tie trunk, page 121

•

SIP trunk for ITSP, page 122

•

Triton T1/PRI trunk, page 125

•

Triton analog trunk, page 128

This chapter also discusses incoming call routing (page 136) and outgoing call blocking 
(page 137), both configurable on tabs in the 

Trunk Configuration

 window.

Trunks Out of Service

If none of the trunks are available when an outside call is placed, the caller will hear the 
system prompt: “All outside lines are busy. Please try again later.”

Channel Identification

To find out channel information, right-click a trunk in the Trunk View window (shown in 
Figure 55, below), and select 

Channel Physical Location

. The Channel Information 

box appears, displaying logical board ID, board name, channel group type, and channel 
ID:

Summary of Contents for ACM 6.7























































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ACM 6.7

Eagle Copters P139-HD Troubleshooting Manual preview
P139-HD
Brand: Eagle Copters Pages: 11
Jäger ADwin-Gold Hardware Manual preview
ADwin-Gold
Brand: Jäger Pages: 50
Yealink CP935W Quick Start Manual preview
CP935W
Brand: Yealink Pages: 8
fadini Coral 1080 Fitting Instructions Manual preview
Coral 1080
Brand: fadini Pages: 12
Daewoo AXL-128 Service Manual preview
AXL-128
Brand: Daewoo Pages: 27
Loewe Audio Center Floor Stand I Compose Operating Instructions And Owner'S Manual preview
Audio Center Floor Stand I Compose
Brand: Loewe Pages: 52
RADVision Scopia XT5000 Series User Manual preview
Scopia XT5000 Series
Brand: RADVision Pages: 55
Grundig MS 235 Manual preview
MS 235
Brand: Grundig Pages: 24
ICS Auto Sentry Petro Installation Manual preview
Auto Sentry Petro
Brand: ICS Pages: 42
Work Pro Roader 408 User Manual preview
Roader 408
Brand: Work Pro Pages: 12
Nibe MODBUS 40 Installer Manual preview
MODBUS 40
Brand: Nibe Pages: 32
AEG BSS 4804 Instruction Manual preview
BSS 4804
Brand: AEG Pages: 58
AEG BSS 4806 Instruction Manual preview
BSS 4806
Brand: AEG Pages: 66
AEG BSS 4808 Manual preview
BSS 4808
Brand: AEG Pages: 90
Fujitsu FT0102A User Manual preview
FT0102A
Brand: Fujitsu Pages: 8
AudioBahn ACAP4P Operating Instructions Manual preview
ACAP4P
Brand: AudioBahn Pages: 14
AMW DIRT User Manual preview
DIRT
Brand: AMW Pages: 44
Aastra Aastra 610d User Manual preview
Aastra 610d
Brand: Aastra Pages: 118

Brands by name

Popular brands

Load more brands