manualshive.com logo in svg

Altigen ACM 6.7, Administrator'S Manual

The Altigen ACM 6.7, a sophisticated communication management system, offers seamless integration of various channels. To maximize user experience, an Administrator's Manual is available for free download at manualshive.com. This comprehensive manual empowers users with detailed instructions and insights, ensuring efficient utilization of the product's diverse features and functionalities.

Share
Download
background image

Limitations

MAXCS ACM 6.7 Administration Manual  365

•

If the board configuration for the default gateway is changed, or the license for the 
SIP-Trunk is changed, you must reboot both the primary and secondary systems to 
make the change take effect. The correct order for reboot is: 1) shut down inactive 
system; 2) shut down active system; 3) start active system; 4) start the inactive 
system.

•

HMCP installed with Softswitch is not supported if VLAN is used. This is because to 
run HMCP, VLAN needs one additional NIC but redundancy supports only two NICs.

•

If the active system needs to be shut down for maintainance, control must be 
manually switched from the active system to the standby system first.

Summary of Contents for ACM 6.7























































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ACM 6.7

VCON HD100 Getting Started Manual preview
HD100
Brand: VCON Pages: 16
Panasonic AFPX-COM5 Upgrade Procedure preview
AFPX-COM5
Brand: Panasonic Pages: 3
Pilz PSS67 IO1 16FDI Operating Manual preview
PSS67 IO1 16FDI
Brand: Pilz Pages: 36
Woodward Vertex-Pro Installation/Hardware Manual preview
Vertex-Pro
Brand: Woodward Pages: 112
Vestil BOL-R Series Instruction Manual preview
BOL-R Series
Brand: Vestil Pages: 6
Advantech AIIS-1440 User Manual preview
AIIS-1440
Brand: Advantech Pages: 82
Polycom SolutionStation 2W User Manual/Administrator Manual preview
SolutionStation 2W
Brand: Polycom Pages: 46
ICT TS-0698 Manual preview
TS-0698
Brand: ICT Pages: 11
SoundMax SM- MSD11 Instruction Manual preview
SM- MSD11
Brand: SoundMax Pages: 43
Taiden HCS-5300 Installation And Operating Manual preview
HCS-5300
Brand: Taiden Pages: 91
Balboa Instruments Poolux Installation And Configuration Manual preview
Poolux
Brand: Balboa Instruments Pages: 76
CAI Countryman Type 10S Stereo Direct Box Manual preview
Countryman Type 10S Stereo Direct Box
Brand: CAI Pages: 16
J.R. Clancy SceneControl 100 Operating Instructions Manual preview
SceneControl 100
Brand: J.R. Clancy Pages: 13
Yealink MVC340-C4-000 Manual preview
MVC340-C4-000
Brand: Yealink Pages: 5
Foxtech T30 User Manual preview
T30
Brand: Foxtech Pages: 63
Boss Audio Systems CAP2C User Manual preview
CAP2C
Brand: Boss Audio Systems Pages: 2
JVC CA-UXG1 Service Manual preview
CA-UXG1
Brand: JVC Pages: 51
JVC CA-D301T Instructions Manual preview
CA-D301T
Brand: JVC Pages: 37

Brands by name

Popular brands

Load more brands