manualshive.com logo in svg

Altera Stratix II GX, User Manual

The Altera Stratix II GX User Manual is your essential guide to understanding and utilizing all the features of this powerful product. Easily accessible for download and free of charge at manualshive.com, this comprehensive manual empowers users to maximize the full potential of the Altera Stratix II GX.

Share
Download
background image

Altera Corporation 

  

2–135

October 2007

Stratix II GX Device Handbook, Volume 2

Stratix II GX Transceiver Architecture Overview

Multiple 
Protocols and 
Data Rates in a 
Transceiver 
Block

Stratix II GX supports multiple protocols and/or data rates in a single 
transceiver block. This allows for better utilization of the channels and 
power savings. There can be up to four independent data rates supported 
and up to two separate frequencies for the TX channels and up to four 
separate frequencies for the RX channels within a single transceiver 
block.

On the TX side, the TX local dividers and the two TXPLLs in the central 
block can be used together or separately to achieve multiple data rates 
and/or protocols in a transceiver block. Refer to 

“Transmitter Local Clock 

Divider Block” on page 2–16

 and 

“Central Clock Divider Block” on 

page 2–14

 for more information regarding the TX local divider blocks and 

the dual TXPLL configuration.

On the RX side, it is possible to have up to four receiver channels to be of 
different data rates and configurations as long as there are enough PLD 
interface clocks to support the channels. Since each receiver channel 
contains a dedicated RXPLL, there are no data rate or configuration 
restrictions. 

Bank15
Basic 4ch

pll_inclk

1

0

Using one 

REFCLK

 pin.

rx_cruclk

4

0

Connect to 

pll_inclk.

rx_clkout

4

4

To PLD fabric.

tx_clkout

4

1

To PLD fabric.

cal_blk_clk

1

1

From PLD fabric.

Bank16
Basic 4ch

pll_inclk

1

0

Using one 

REFCLK

 pin.

rx_cruclk

4

0

Connect to 

pll_inclk.

rx_clkout

4

4

To PLD fabric.

tx_clkout

4

1

To PLD fabric.

Bank17
PCIE ×4

pll_inclk

1

0

Using one 

REFCLK

 pin.

rx_cruclk

4

0

Connect to 

pll_inclk.

coreclkout

1

1

To PLD fabric.

fixedclk

1

1

From PLD fabric.

Region2 LRIO Clock

8/8 (or 7/8, 6/8)

Region3 LRIO Clock

5/8 (or 6/8, 7/8)

Table 2–30. Example of LRIO Clock Resource Usage  (Part 2 of 2)

Clock Name

Number of 

Signals in the 

Transceiver 

Block

LRIO Resource 

Usage

Routing

Summary of Contents for Stratix II GX

































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Stratix II GX

Offshore 5801 User Manual preview
5801
Brand: Offshore Pages: 14
LAPIS Semiconductor ML7344 Start Manual preview
ML7344
Brand: LAPIS Semiconductor Pages: 12
Quark-Elec QK-A026+ Setup Manual preview
QK-A026+
Brand: Quark-Elec Pages: 2
S&C SpeedNet Instruction Sheet preview
SpeedNet
Brand: S&C Pages: 62
YOODA MAGNETIC PRO YSH Instruction Manual preview
MAGNETIC PRO YSH
Brand: YOODA Pages: 2
emitor Satlook Micro G2 User Manual preview
Satlook Micro G2
Brand: emitor Pages: 24
Navilock NL-6003P Operation Manual preview
NL-6003P
Brand: Navilock Pages: 9
Williams Sound WIR 125 Manual And User Manual preview
WIR 125
Brand: Williams Sound Pages: 14
Easy wave neo RCP20 Quick Start Manual preview
neo RCP20
Brand: Easy wave Pages: 4
Eltek GS42AVE User Instructions preview
GS42AVE
Brand: Eltek Pages: 2
Icom IC-F110S Instruction Manual preview
IC-F110S
Brand: Icom Pages: 20
Sansui SQ-115 Instruction Manual preview
SQ-115
Brand: Sansui Pages: 28
DAITEM DP8000 Series Manual preview
DP8000 Series
Brand: DAITEM Pages: 44
Zamel Sundi ST-251 Manual preview
Sundi ST-251
Brand: Zamel Pages: 21
Daiichi Electronics AETT2-91A Instruction Manual preview
AETT2-91A
Brand: Daiichi Electronics Pages: 12
Keller-druck 41 X Ei Series Manual preview
41 X Ei Series
Brand: Keller-druck Pages: 2
HESCH HE 5409 Operating Instructions Manual preview
HE 5409
Brand: HESCH Pages: 16
Sirius Satellite Radio Starmate ST1 User Manual preview
Starmate ST1
Brand: Sirius Satellite Radio Pages: 36

Brands by name

Popular brands

Load more brands