manualshive.com logo in svg

Altera Stratix II GX, User Manual

The Altera Stratix II GX User Manual is your essential guide to understanding and utilizing all the features of this powerful product. Easily accessible for download and free of charge at manualshive.com, this comprehensive manual empowers users to maximize the full potential of the Altera Stratix II GX.

Share
Download
background image

Altera Corporation 

  

3–81

October 2007

Stratix II GX Device Handbook, Volume 2

Stratix II GX Dynamic Reconfiguration

Table 3–6

 provides descriptions for the 

tx_datainfull

 and 

rx_dataoutfull

 signals for GIGE and SONET/SDH OC48 modes.

Clocking

For the transmit side, the PLD logic for the SONET/SDH OC48 and GIGE 
modes sends the data synchronized to the 

tx_clkout

 signal. Therefore, 

the clocking for the transmit side remains the same for the two modes.

For the receive side, the data and status signals from the ALT2GXB 
megafunction for the GIGE mode is synchronized to 

tx_clkout

 since 

rate matching is used. For the SONET/SDH OC48 mode, the signals are 
synchronized to 

rx_clkout

. Therefore, the PLD logic has two functional 

protocol-specific logic blocks to handle data for the GIGE and 
SONET/SDH OC48 modes. Based on the configured protocol mode, the 
receive side logic selects the appropriate data path.

Table 3–6. PLD Interface Signals—GIGE and SONET/SDH OC48 Modes 

Signal Name

Description

GIGE MODE

tx_datainfull[7:0]

8-bit unencoded data input to the 
transceiver channel

tx_datainfull[8]

tx_ctrlenable

 (control signal K/D)

rx_dataoutfull[7:0]

8-bit unencoded data output from the 
transceiver channel

rx_dataoutfull[8]

rx_ctrldetect

 (control signal K/D)

rx_dataoutfull[9]

rx_errdetect

rx_dataoutfull[10]

rx_syncstatus

rx_dataoutfull[11]

rx_disperr

rx_dataoutfull[12]

rx_patterndetect

SONET/SDH OC48 MODE

tx_datainfull[7:0]

LSB data input to the transceiver channel

tx_datainfull[29:22]

MSB data input to the transceiver channel

rx_dataoutfull[7:0]

LSB data output from the transceiver 
channel

rx_dataoutfull[29:22

MSB data output from the transceiver 
channel

rx_dataoutfull[10], 

rx_dataoutfull[42]

rx_syncstatus[1:0]

rx_dataoutfull[12], 

rx_dataoutfull[44]

rx_patterndetect[1:0]

Summary of Contents for Stratix II GX

































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Stratix II GX

ABB TB82EC Quick Programming Manual preview
TB82EC
Brand: ABB Pages: 2
Takstar X4 Manual preview
X4
Brand: Takstar Pages: 24
Harman Kardon Stratophonic SR300B Owner'S Manual preview
Stratophonic SR300B
Brand: Harman Kardon Pages: 10
Harman Kardon BRUKSANVISNING AVR 255 Användarhandbok preview
BRUKSANVISNING AVR 255
Brand: Harman Kardon Pages: 58
Harman Kardon AVR 8000 Owner'S Manual preview
AVR 8000
Brand: Harman Kardon Pages: 60
Harman Kardon AVR 7550HD Quick Start Manual preview
AVR 7550HD
Brand: Harman Kardon Pages: 2
Harman Kardon AVR 7550HD Worksheet preview
AVR 7550HD
Brand: Harman Kardon Pages: 7
Harman Kardon AVR 70 Owner'S Manual preview
AVR 70
Brand: Harman Kardon Pages: 34
Harman Kardon AVR 630 Test Report preview
AVR 630
Brand: Harman Kardon Pages: 2
Harman Kardon AVR 3600 User Manual preview
AVR 3600
Brand: Harman Kardon Pages: 2
Harman Kardon AVR 335 Quick Start Manual preview
AVR 335
Brand: Harman Kardon Pages: 4
Harman Kardon AVR 2550 Specification preview
AVR 2550
Brand: Harman Kardon Pages: 2
Harman Kardon AVR 3500 Service Manual preview
AVR 3500
Brand: Harman Kardon Pages: 52
Harman Kardon AVR 430 Quick Start Manual preview
AVR 430
Brand: Harman Kardon Pages: 4
Harman Kardon NOCTURNE 210 Product Information preview
NOCTURNE 210
Brand: Harman Kardon Pages: 2
Harman Kardon AVR 2650 Quick Start Manual preview
AVR 2650
Brand: Harman Kardon Pages: 10
Harman Kardon AVR 1700 Quick Setup Manual preview
AVR 1700
Brand: Harman Kardon Pages: 140
Harman Kardon AVR 1510 Service Manual preview
AVR 1510
Brand: Harman Kardon Pages: 131

Brands by name

Popular brands

Load more brands