manualshive.com logo in svg

Altera Stratix II GX, User Manual

The Altera Stratix II GX User Manual is your essential guide to understanding and utilizing all the features of this powerful product. Easily accessible for download and free of charge at manualshive.com, this comprehensive manual empowers users to maximize the full potential of the Altera Stratix II GX.

Share
Download
background image

Altera Corporation 

  

2–27

October 2007

Stratix II GX Device Handbook, Volume 2

Stratix II GX Transceiver Architecture Overview

A five transceiver device (EP2SGX130G) supports up to two PCI-E ×8 
links (refer to 

Figure 2–15

). The transceiver block pairs are the same as in 

the four transceiver device—blocks 0 and 1 and blocks 2 and 3. Block 4 is 
not used for PCI-E ×8 mode. If any transceiver blocks are not used in the 
PCI-E ×8 mode, they can be used to support any other protocol.

Figure 2–15. Five Transceiver Block Device With Two ×8 PCI-E Links

 

Note (1)

Note to 

Figure 2–15

:

(1)

Transceiver Bank 17 can be active and used to support other protocols. 

GXB_TX/RX1

GXB_TX/RX0

GXB_TX/RX2

GXB_TX/RX3

GXB_TX/RX5
GXB_TX/RX4

GXB_TX/RX6

GXB_TX/RX7

EP2SGX130GF

PCIe Lane 4

PCIe Lane 5

PCIe Lane 7

PCIe Lane 6

PCIe Lane 0

PCIe Lane 1

PCIe Lane 3

PCIe Lane 2

Bank 13 (Slave)

Bank 14 (Master)

GXB_TX/RX9

GXB_TX/RX8

GXB_TX/RX10

GXB_TX/RX11

GXB_TX/RX13

GXB_TX/RX12

GXB_TX/RX14

GXB_TX/RX15

PCIe Lane 4

PCIe Lane 5

PCIe Lane 7

PCIe Lane 6

PCIe Lane 0

PCIe Lane 1

PCIe Lane 3

PCIe Lane 2

First PIPE x8 

Channel 

Second PIPE x8 

Channel 

GXB_TX/RX17

GXB_TX/RX16
GXB_TX/RX18

GXB_TX/RX19

Bank 17

Bank 15 (Slave)

Bank 16 (Master)

Summary of Contents for Stratix II GX

































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Stratix II GX

Abilia Andromeda Faq Manual preview
Andromeda
Brand: Abilia Pages: 6
Garmin gWind Race Installation Instructions Manual preview
gWind Race
Brand: Garmin Pages: 44
Raymarine AIS700 Installation Instructions Manual preview
AIS700
Brand: Raymarine Pages: 52
Yaesu FT-70DR Operating Manual preview
FT-70DR
Brand: Yaesu Pages: 44
Badger Meter 345WT Installation & Operation Manual preview
345WT
Brand: Badger Meter Pages: 4
Xblitz X450 Manual preview
X450
Brand: Xblitz Pages: 76
Tevion MD 81157 Manual preview
MD 81157
Brand: Tevion Pages: 22
Tyco Security Products SG-System 5 Operating Manual preview
SG-System 5
Brand: Tyco Security Products Pages: 108
Hokuyo DMS Series Instruction Manual preview
DMS Series
Brand: Hokuyo Pages: 2
Vaisala HUMICAP HMW90 SERIES Quick Manual preview
HUMICAP HMW90 SERIES
Brand: Vaisala Pages: 118
NOSHOK King-Gage 5800 Series Installation And Operation Instruction Manual preview
King-Gage 5800 Series
Brand: NOSHOK Pages: 12
Topfield CBV-7100 User Manual preview
CBV-7100
Brand: Topfield Pages: 46
Sab Satellite Titan III Combo HD User Manual preview
Titan III Combo HD
Brand: Sab Satellite Pages: 43
Vestamatic VRS Switch 1 Installation And Operating Instructions preview
VRS Switch 1
Brand: Vestamatic Pages: 2
Xoro HRS 2500 Operation Manual preview
HRS 2500
Brand: Xoro Pages: 90
R.V.R. Electronica BLUES30 User Manual preview
BLUES30
Brand: R.V.R. Electronica Pages: 32
Vaisala CARBOCAP GMM112 Quick Reference Manual preview
CARBOCAP GMM112
Brand: Vaisala Pages: 2
Ham radio KN920 Operation Manual preview
KN920
Brand: Ham radio Pages: 14

Brands by name

Popular brands

Load more brands