manualshive.com logo in svg

Altera Stratix II GX, User Manual

The Altera Stratix II GX User Manual is your essential guide to understanding and utilizing all the features of this powerful product. Easily accessible for download and free of charge at manualshive.com, this comprehensive manual empowers users to maximize the full potential of the Altera Stratix II GX.

Share
Download
background image

3–22

  

Altera Corporation

Stratix II GX Device Handbook, Volume 2

October 2007

Channel and PMA Controls Reconfiguration

The following are control signals (other than the 

write_all

 and 

reconfig_mode_sel

 signals):

■

logical_channel_address[7:0]

: Use this control signal to set 

the logical channel number of the channel that is being reconfigured 
by the dynamic reconfiguration controller. This signal gets enabled 
when the number of channels controlled by the dynamic 
reconfiguration controller is more than one. Since the channel 
reconfiguration is done on a per-channel basis, you have to use this 
signal and provide the necessary logical channel address to write the 
MIF words so that a successful channel reconfiguration is achieved 
for that channel. 

■

reset_reconfig_address

: Use this optional control signal to 

reset the 

reconfig_address_out

 value to 

0

. This reset control 

signal is only applicable in channel reconfiguration. 

The following are status signals (other than the 

busy

 signal):

■

reconfig_address_en

: This is an optional output signal. The 

ALT2GXB_RECONFIG asserts this signal to indicate the change in 
value on the 

reconfig_address_out

 port. This signal only gets 

asserted after the dynamic reconfiguration controller completes 
writing the 16-bit data. 

■

reconfig_address_out[4:0]

: This is an optional output signal. 

It provides the address value that you can use to read the appropriate 
word from the MIF. Use the value in this port in combination with the 

reconfig_address_en

 signal to decide when to initiate a new 

write transaction.

■

channel_reconfig_done

: This signal is available when you select 

the 

Channel Reconfiguration

 option in the dynamic reconfiguration 

controller. This port indicates that the ALT2GXB_RECONFIG 
megafunction has finished writing all the words of a MIF in a 
sequence. This signal is very useful for user logic to implement reset 
recommendations during and after dynamic reconfiguration. Refer 
to 

“Reset Recommendations” on page 3–66

 for more information 

about using this signal.

Summary of Contents for Stratix II GX

































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Stratix II GX

UNIBOX HD ECO+ Instruction Manual preview
HD ECO+
Brand: UNIBOX Pages: 59
R.L.DRAKE T-4X Instruction Manual preview
T-4X
Brand: R.L.DRAKE Pages: 46
Tait T835 User Manual preview
T835
Brand: Tait Pages: 72
sunair gsb-900 dx Operation And Maintenance Manual preview
gsb-900 dx
Brand: sunair Pages: 188
Kramer C-A35M/IRR-03 Installation Instructions preview
C-A35M/IRR-03
Brand: Kramer Pages: 2
jotron TRON AIR User Manual preview
TRON AIR
Brand: jotron Pages: 32
Sangean H203D Manual preview
H203D
Brand: Sangean Pages: 26
TURBO RACING 91803G-VT Instruction Manual preview
91803G-VT
Brand: TURBO RACING Pages: 4
Camille Bauer KINAX 3W2 Operating Instructions preview
KINAX 3W2
Brand: Camille Bauer Pages: 5
SLEIPNER MOTOR AS SIDE-POWER RCS-10E Installation & User Manual preview
SIDE-POWER RCS-10E
Brand: SLEIPNER MOTOR AS Pages: 12
Spektrum SRS6000 Instruction Manual preview
SRS6000
Brand: Spektrum Pages: 14
Cooper Security Scantronic 734r Series Manual preview
Scantronic 734r Series
Brand: Cooper Security Pages: 80
Goodmans GDB7CA User Manual preview
GDB7CA
Brand: Goodmans Pages: 20
THOMSON CS1200VD - PART 1 Manual preview
CS1200VD - PART 1
Brand: THOMSON Pages: 9
POLMAR SMART PMR446 User Manual preview
SMART PMR446
Brand: POLMAR Pages: 32
Harman Kardon CITATION 24 Owner'S Manual preview
CITATION 24
Brand: Harman Kardon Pages: 16
M-system JTY2 Instruction Manual preview
JTY2
Brand: M-system Pages: 7
CDVI S3TR2641T1 Quick Start Manual preview
S3TR2641T1
Brand: CDVI Pages: 2

Brands by name

Popular brands

Load more brands