manualshive.com logo in svg

Altera Stratix II GX, User Manual

The Altera Stratix II GX User Manual is your essential guide to understanding and utilizing all the features of this powerful product. Easily accessible for download and free of charge at manualshive.com, this comprehensive manual empowers users to maximize the full potential of the Altera Stratix II GX.

Share
Download
background image

3–48

  

Altera Corporation

Stratix II GX Device Handbook, Volume 2

October 2007

Channel and PMA Controls Reconfiguration

Figure 3–24

 shows a setup with all the transmitters configured at 3 Gbps 

and each one at a unique functional mode. Each channel can be switched 
to a different functional mode using the channel reconfiguration feature 
of the dynamic reconfiguration controller. In this case, option 2 is 
applicable.

Figure 3–25. Option 2: Channel Reconfiguration—Transmit Core Clocking

Receiver Core Clocking

Receiver core clocking is the read clocking options for the Receive Phase 
Comp FIFO. The receiver core clocking is used to read the parallel data 
into the Receive Phase Comp FIFO from the PLD interface. The possible 
transmit core clock options are:

■

rx_clkout

 (the Quartus II software automatically routes to PLD 

and back into Phase Comp)

■

rx_coreclk

 (user-supplied input clock)

Dynamic reconfiguration supports both receive clock options. The 
ALT2GXB MegaWizard only asks for the 

rx_clkout

 settings. The 

Quartus II software automatically routes the clock paths based on a given 
mode setup. You must verify that clock routing is compatible with each 

CMU
PLL0

TX1 (3 Gbps)

RX1

TX0 (3 Gbps)

RX0

TX2 (3 Gbps)

RX2

TX3 (3 Gbps)

RX3

CMU
PLL1

Summary of Contents for Stratix II GX

































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Stratix II GX

halstrup-walcher P29 Instruction Manual preview
P29
Brand: halstrup-walcher Pages: 23
Hanwha Techwin SBP-329HM Quick Start Manual preview
SBP-329HM
Brand: Hanwha Techwin Pages: 2
Hanwha Techwin SBP-201HM Quick Start Manual preview
SBP-201HM
Brand: Hanwha Techwin Pages: 2
Yaesu FT-7900R Operating Manual preview
FT-7900R
Brand: Yaesu Pages: 84
Yaesu FT-7800R Brochure & Specs preview
FT-7800R
Brand: Yaesu Pages: 2
Yaesu FT-747GX Operating Manual preview
FT-747GX
Brand: Yaesu Pages: 42
Yaesu FT-5200 User Manual preview
FT-5200
Brand: Yaesu Pages: 46
Yaesu FT-991 Key Press Sequences preview
FT-991
Brand: Yaesu Pages: 2
Yaesu FT-991 Reference Book preview
FT-991
Brand: Yaesu Pages: 20
Yaesu FT-991 Operating Manual preview
FT-991
Brand: Yaesu Pages: 96
Yaesu FT-8800R Technical Supplement preview
FT-8800R
Brand: Yaesu Pages: 55
Yaesu FT-60R Specifications preview
FT-60R
Brand: Yaesu Pages: 2
Yaesu FT-51R Owner'S Manual preview
FT-51R
Brand: Yaesu Pages: 78
Yaesu FT DX 9000 CONTEST - 2 Technical Supplement preview
FT DX 9000 CONTEST - 2
Brand: Yaesu Pages: 410
Yaesu FT-857 series Operation Manual preview
FT-857 series
Brand: Yaesu Pages: 132
Yaesu FT-100 Micro Mobile Undocumented preview
FT-100 Micro Mobile
Brand: Yaesu Pages: 55
Yaesu FT-2000 - MENU MODE LIST Technical Supplement preview
FT-2000 - MENU MODE LIST
Brand: Yaesu Pages: 206
Yaesu FTM-400XDR Operating Manual preview
FTM-400XDR
Brand: Yaesu Pages: 17

Brands by name

Popular brands

Load more brands