manualshive.com logo in svg

Altera Stratix II GX, User Manual

The Altera Stratix II GX User Manual is your essential guide to understanding and utilizing all the features of this powerful product. Easily accessible for download and free of charge at manualshive.com, this comprehensive manual empowers users to maximize the full potential of the Altera Stratix II GX.

Share
Download
background image

Altera Corporation 

  

2–147

October 2007

Stratix II GX Device Handbook, Volume 2

Stratix II GX Transceiver Architecture Overview

Figure 2–110

 shows the data path in this mode.

Figure 2–110. Basic Single-Width Mode with ×4 Clocking

The transmitter data path consists of a 16-bit PLD-transceiver interface, 
transmitter phase compensation FIFO, 16:8-bit byte serializer, and 8:1 
serializer.

The receiver data path consists of the clock recovery unit (CRU), 1:8 
deserializer, bit-slip word aligner, 8:16 byte deserializer, receiver phase 
compensation FIFO, and 16-bit Transceiver-PLD interface.

Transceiver Placement Limitations

If one or more channels in a transceiver block are configured to Basic 
single-width mode with ×4 clocking option enabled, the remaining 
channels in that transceiver block must either have the same 
configuration or must be unused. All used channels within a transceiver 
block configured to this mode must also run at the same data rate. All 
channels within the transceiver block configured to this mode must be 
instantiated using the same ALT2GXB MegaWizard instance. 

Transmitter Digital Logic

Receiver Digital Logic

Analog Receiver and
Transmitter Logic

FPGA

Logic
Array

TX Phase

Compensation

FIFO

RX Phase

Compen-

sation

FIFO

Byte

Serializer

8B/10B

Encoder

Serializer

Clock

Recovery

Unit

Word

Aligner

Deskew

FIFO

8B/10B

Decoder

Byte

De-

serializer

Byte

Ordering

Rate

Match

FIFO

De-

serializer

Summary of Contents for Stratix II GX

































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Stratix II GX

EB TECHNOLOGY RX1 Instructions Manual preview
RX1
Brand: EB TECHNOLOGY Pages: 12
Paradox RX1 Quick Start Manual preview
RX1
Brand: Paradox Pages: 2
Datcon DT1012 Operating Instructions Manual preview
DT1012
Brand: Datcon Pages: 40
MuxLab 500028-WP-UK Quick Installation Manual preview
500028-WP-UK
Brand: MuxLab Pages: 2
Raymarine Realvision RV-220P Installation Instructions Manual preview
Realvision RV-220P
Brand: Raymarine Pages: 24
Tesla TE-380 Mini User Manual preview
TE-380 Mini
Brand: Tesla Pages: 68
IFR Systems AM-1600S Maintenance Manual preview
AM-1600S
Brand: IFR Systems Pages: 204
Artel FiberLink 4160 Series Installation And Operation Manual preview
FiberLink 4160 Series
Brand: Artel Pages: 12
NPG DTR 1002S PRO User Manual preview
DTR 1002S PRO
Brand: NPG Pages: 28
SenseAir tSense User Manual preview
tSense
Brand: SenseAir Pages: 14
Integra A1113 Instruction Manual preview
A1113
Brand: Integra Pages: 48
O-Lynx Radio Kit Manual preview
Radio Kit
Brand: O-Lynx Pages: 16
Jamara Compa XR3 Instructions Manual preview
Compa XR3
Brand: Jamara Pages: 12
Macally POD-FM User Manual preview
POD-FM
Brand: Macally Pages: 12
X-Digital System PRO4 User Manual preview
PRO4
Brand: X-Digital System Pages: 45
t.a.c. CP-8551 General Instructions Manual preview
CP-8551
Brand: t.a.c. Pages: 8
Yaesu FTM-500DR Instruction Manual preview
FTM-500DR
Brand: Yaesu Pages: 32
Swisson UM-XSW-D0-LEN-V03-01 User Manual preview
UM-XSW-D0-LEN-V03-01
Brand: Swisson Pages: 16

Brands by name

Popular brands

Load more brands