manualshive.com logo in svg

Altera Stratix II GX, User Manual

The Altera Stratix II GX User Manual is your essential guide to understanding and utilizing all the features of this powerful product. Easily accessible for download and free of charge at manualshive.com, this comprehensive manual empowers users to maximize the full potential of the Altera Stratix II GX.

Share
Download
background image

Altera Corporation 

  

3–101

October 2007

Stratix II GX Device Handbook, Volume 2

Stratix II GX Dynamic Reconfiguration

Figure 3–46. Transceiver Channel Default Configuration

Consider that you intend to switch to the following two modes:

mode1: 

■

Full-duplex channel with the main TXPLL configured to 6.25 Gbps 
data using a 156.25 MHz reference clock. Assume that the 
logical tx pll is set to 

0

 for the main TXPLL. 

■

Rate matcher is not enabled in the ALT2GXB megafunction.

■

The alternate TXPLL is configured to 2.5 Gbps using a 125 MHz 
reference clock. 

mode2:

■

Full-duplex channel with the main TXPLL configured to 5 Gbps data 
using a 156.25 MHz reference clock. Assume that the logical tx pll is 
set to 

0

 for the main TXPLL. 

■

Rate matcher is enabled in the ALT2GXB megafunction.

■

The alternate TXPLL is configured to 2.5 Gbps using a 125 MHz 
reference clock. 

Consider that the MIF is generated for mode1 and mode2. (Details on the 
steps to generate the MIF are covered later in this section. The intent of 
this example is to show how the functional blocks are reconfigured based 
on the feature used).

/1

pll_inclk_rx_cruclk[1] 

156.25 MHz

125 MHz

pll_inclk_rx_cruclk[0]

Clock Multiplier Unit

5 Gbps

LOGICAL

TXPLL0

2.5 Gbps

LOGICAL

TXPLL1

clock
MUX

clock
MUX

Full Duplex Transceiver Channel

TX CHANNEL

RX CHANNEL

5 Gbps

d analog logic

LOCAL

DIVIDER

Logical

TX PLL

Select

clock
MUX

5 Gbps

RX PLL

5 Gbps

d analog logic

Summary of Contents for Stratix II GX

































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Stratix II GX

Samsung DSR 3700 Instructions For Use Manual preview
DSR 3700
Brand: Samsung Pages: 19
Radionics D6500 Installation Manual preview
D6500
Brand: Radionics Pages: 73
Kathrein UFT 671si Operating Manual preview
UFT 671si
Brand: Kathrein Pages: 44
Watkins Johnson WJ-8711A Technical Data Manual preview
WJ-8711A
Brand: Watkins Johnson Pages: 9
Intelix AVO-A4-WP110-EU Installation Manual preview
AVO-A4-WP110-EU
Brand: Intelix Pages: 4
Magellan ProMark 500 Getting Started Manual preview
ProMark 500
Brand: Magellan Pages: 42
Xantech Dinky Link 480B-30 Install Manual preview
Dinky Link 480B-30
Brand: Xantech Pages: 3
Kramer 617T Installation Instructions preview
617T
Brand: Kramer Pages: 4
Elecom LBT-PAR02 Series Manual preview
LBT-PAR02 Series
Brand: Elecom Pages: 2
Sencore TXS 3800 Quick Start Manual preview
TXS 3800
Brand: Sencore Pages: 3
YEONHWA M TECH DX-8000 Series User Manual preview
DX-8000 Series
Brand: YEONHWA M TECH Pages: 19
Watts Vision BT-PR02 RF Manual preview
Vision BT-PR02 RF
Brand: Watts Pages: 16
Dakota Micro AgCam DMAC-RH User Manual preview
AgCam DMAC-RH
Brand: Dakota Micro Pages: 2
Omicron Lab B-LFT 100 User Manual preview
B-LFT 100
Brand: Omicron Lab Pages: 24
CYP DCT-30RX Operator'S Manual preview
DCT-30RX
Brand: CYP Pages: 12
Steren FMT-600 Quick Start Manual preview
FMT-600
Brand: Steren Pages: 3
Alpine iLX-F309 Installation Manual preview
iLX-F309
Brand: Alpine Pages: 64
Anthem MRX 310 Assembly Instructions preview
MRX 310
Brand: Anthem Pages: 2

Brands by name

Popular brands

Load more brands