Altera Stratix II GX Page 388 User Manual Download

Page: 388 / 672

3–140

Altera Corporation

Stratix II GX Device Handbook, Volume 2

October 2007

Adaptive Equalization (AEQ)

with

logical_channel_address

value of

Figure 3–67

shows the

connections between multiple ALT2GXB instances and the dynamic
reconfiguration controller.

Figure 3–67. Interface Connection Between the ALT2GXB and the ALT2GXB_RECONFIG Instance

The

fixedclk

port provides the clock input to run the AEQ hardware.

The range of the input clock frequency to the

fixedclk

port should be

between 2.5 MHz and 125 MHz. To save clock routing resources, you can
use the same clock pin to provide input clocks for the

fixedclk

and

reconfig_clk

ports.

When the transceiver channel is configured for PCI-Express
(PIPE) protocol, the

fixedclk

is used to operate the receiver

detect circuitry. In this protocol mode,

fixedclk

requires a

fixed 125 MHz input clock frequency. The AEQ feature is not
available in PCI-Express (PIPE) protocol mode.

ALT2GXB_
RECONFIG

aeq_togxb[7:0]

aeq_fromgxb[11:0]

aeq_fromgxb[5:0]

aeq_togxb[3:0]

aeq_togxb[7:4]

aeq_fromgxb[11:6]

ALT2GXB Instance 0

starting channel number=0

ALT2GXB Instance 1

starting channel number=4

Summary of Contents for Stratix II GX

































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Stratix II GX

Reviews:

Related manuals for Stratix II GX

Brands by name

Popular brands

Altera Stratix II GX, User Manual

Search results

Summary of Contents for Stratix II GX

Reviews:

Related manuals for Stratix II GX

Brands by name

Popular brands