manualshive.com logo in svg

Altera Stratix II GX, User Manual

The Altera Stratix II GX User Manual is your essential guide to understanding and utilizing all the features of this powerful product. Easily accessible for download and free of charge at manualshive.com, this comprehensive manual empowers users to maximize the full potential of the Altera Stratix II GX.

Share
Download
background image

Altera Corporation 

  

2–197

October 2007

Stratix II GX Device Handbook, Volume 2

Stratix II GX Transceiver Architecture Overview

Transmitter Data Path

In the 10-bit channel width SDI configuration, the transmitter data path is 
made up of the transmitter phase compensation FIFO and the 10:1 
serializer. In the 20-bit channel width SDI configuration, the transmitter 
data path also includes the byte serializer.

1

In SDI mode, the transmitter is purely a parallel-to-serial 
converter. SDI transmitter functions, such as scrambling and 
cyclic redundancy check (CRC) code generation, must be 
implemented in the FPGA logic array.

Receiver Data Path

In the 10-bit channel width SDI configuration, the receiver data path 
comprises of the clock recovery unit (CRU), the 1:10 deserializer, the word 
aligner in bit-slip mode, and the receiver phase compensation FIFO. In 
the 20-bit channel width SDI configuration, the receiver data path also 
includes the byte deserializer.

1

SDI receiver functions, such as de-scrambling, framing, and 
CRC checker, must be implemented in the FPGA logic array. 

Receiver Word Alignment/Framing

In SDI systems, since the word alignment and framing happens after 
de-scrambling, the word aligner in the receiver data path is not useful. 
Altera recommends driving the ALT2GXB 

rx_bitslip

 signal low to 

avoid the word aligner from inserting bits in the received data stream.

1

Altera offers SDI MegaCore function that can be configured at 
SD-SDI, HD-SDI, and 3G-SDI data rates. The SDI MegaCore 
function implements system-level functions like scrambling and 
de-scrambling and CRC generation and checking. It also offers 
the capability of configuring the three SDI data rates (SD, HD, 
and 3G) dynamically on the same transceiver channel. For more 
details, refer the

 SDI MegaCore Function User Guide

.

Serial RapidIO Mode

The RapidIO™ Trade Association defines a high-performance, 
packet-switched interconnect standard to pass data and control 
information between microprocessors, digital signal, communications, 
and network processors, system memories, and peripheral devices. 

Summary of Contents for Stratix II GX

































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Stratix II GX

Manaras Opera 100 Series Specifications And Programming Instructions preview
100 Series
Brand: Manaras Opera Pages: 4
Hach si792 D series Quick Start Manual preview
si792 D series
Brand: Hach Pages: 2
Yaesu FTDX10 Technical Supplement preview
FTDX10
Brand: Yaesu Pages: 120
M/A-Com MAVM-VMCLL Product Manual preview
MAVM-VMCLL
Brand: M/A-Com Pages: 62
Jackson Labs Micro-JLT GNSS User Manual preview
Micro-JLT GNSS
Brand: Jackson Labs Pages: 83
l-com LCTP-10BT-10B5 Installation Manual preview
LCTP-10BT-10B5
Brand: l-com Pages: 6
E+E Elektronik EE22 Series Manual preview
EE22 Series
Brand: E+E Elektronik Pages: 36
S&T TSB48-FR User Manual preview
TSB48-FR
Brand: S&T Pages: 13
Yaesu FTA-750L Operating Manual preview
FTA-750L
Brand: Yaesu Pages: 96
Dolphin STM 429J User Manual preview
STM 429J
Brand: Dolphin Pages: 17
CAMDEN Lazerpoint CM-TX-9 Installation Instructions preview
Lazerpoint CM-TX-9
Brand: CAMDEN Pages: 3
Boston DTT8100 User Manual preview
DTT8100
Brand: Boston Pages: 48
Aerospace Logic FF200X Series Operation Manual preview
FF200X Series
Brand: Aerospace Logic Pages: 2
Sagem DTR94 HD FREESAT User Manual preview
DTR94 HD FREESAT
Brand: Sagem Pages: 48
silentgliss SG 10303 Operating Instructions Manual preview
SG 10303
Brand: silentgliss Pages: 29
iGage iG4 User Manual preview
iG4
Brand: iGage Pages: 57
Spektrum SR415 Instruction Manual preview
SR415
Brand: Spektrum Pages: 36
Zodiac DZR-1500FTA User Manual preview
DZR-1500FTA
Brand: Zodiac Pages: 87

Brands by name

Popular brands

Load more brands