manualshive.com logo in svg

Altera Stratix II GX, User Manual

The Altera Stratix II GX User Manual is your essential guide to understanding and utilizing all the features of this powerful product. Easily accessible for download and free of charge at manualshive.com, this comprehensive manual empowers users to maximize the full potential of the Altera Stratix II GX.

Share
Download
background image

3–6

  

Altera Corporation

Stratix II GX Device Handbook, Volume 2

October 2007

Dynamic Reconfiguration Controller Architecture

Figure 3–2. Dynamic Reconfiguration Interface

Notes to 

Figure 3–2

:

(1)

Optional control and status signals. At least one control signal must be enabled if only analog settings 
reconfiguration is enabled.

(2)

If the channel reconfiguration feature is selected in the ALT2GXB_RECONFIG MegaWizard, the  

reconfig_address_out

 is 5-bits wide [4..0]. If the Channel and TXPLL select/reconfig feature is selected, the 

reconfig_address_out

 is 6-bits wide [5..0]. 

The 

reconfig_mode_sel

 signal determines the reconfiguration mode. 

This control signal is 3-bits wide if the 

Adaptive Equalization control

 

option is 

not

 selected. If this option is selected, the 

reconfig_mode_sel

 

signal is 4-bits wide. Encoding of the 

reconfig_mode_sel

 signal 

(when the 

Adaptive Equalization control

 option is 

not

 selected) is as 

follows:

■

reconfig_mode_sel [2:0]

:

●

000 – Reconfiguration of Analog controls. The Analog controls 
feature has been enabled in the Quartus II software version 6.0 
and later 

●

001 – Channel Reconfiguration

●

011 – Dynamic Transmit rate switch

●

100, 101, 110 – Channel and CMU PLL Reconfiguration

rx_eqdcgain[1..0] 

(1)

Dynamic

Reconfig

reconfig_clk

reconfig_fromgxb

tx_preemp_1t[3..0] 

(1)

read

write_all

tx_vodctrl[2..0] 

(1)

rx_eqctrl[3..0] 

(1)

tx_preemp_0t[3..0] 

(1)

reconfig_togxb[2..0]

data_valid

tx_preemp_2t_out[3..0] 

(1)

busy

tx_vodctrl_out[2..0] 

(1)

rx_eqctrl_out[3..0] 

(1)

rx_eqdcgain_out[1..0] 

(1)

tx_preemp_0t_out[3..0] 

(1)

tx_preemp_1t_out[3..0] 

(1)

tx_preemp_2t[3..0] 

(1)

reconfig_mode_sel[]

channel_reconfig_done

reconfig_address_en

reconfig_address_out[5..0] 

(2)

rate_switch_ctrl [1..0]

rate_switch_out [1..0]

reconfig_data[15..0] 

reset_reconfig_address 

logical_tx_pll_sel_en

logical_tx_pll_sel

error

Summary of Contents for Stratix II GX

































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Stratix II GX

Harman Kardon 930 Technical Manual preview
930
Brand: Harman Kardon Pages: 15
Icom GM600 Basic Manual preview
GM600
Brand: Icom Pages: 26
Barlow Wadley XCR 30 Operating Instructions Manual preview
XCR 30
Brand: Barlow Wadley Pages: 13
Yamaha RX-V485 Owner'S Manual preview
RX-V485
Brand: Yamaha Pages: 155
Vaisala Humicap HMD60Y Operating Manual preview
Humicap HMD60Y
Brand: Vaisala Pages: 20
La Crosse Technology TX38U-IT Quick Start Manual preview
TX38U-IT
Brand: La Crosse Technology Pages: 2
Guangzhou Chuanzhou Electronic Technology CZH-10A Manual preview
CZH-10A
Brand: Guangzhou Chuanzhou Electronic Technology Pages: 12
SpeakerCraft Vital 710 Installation Instructions Manual preview
Vital 710
Brand: SpeakerCraft Pages: 36
Alinco DR-599E Operator'S Manual preview
DR-599E
Brand: Alinco Pages: 16
Aventura FBR-1VS-TX Instruction Manual preview
FBR-1VS-TX
Brand: Aventura Pages: 6
Tiviar Alpha Plus User Manual preview
Alpha Plus
Brand: Tiviar Pages: 72
tbs electronics TBS6908 User Manual preview
TBS6908
Brand: tbs electronics Pages: 20
BAPI Wireless Room Temperature Transmitter Installation And Operating Instructions preview
Wireless Room Temperature Transmitter
Brand: BAPI Pages: 2
Lafayette STARFLITE KT-390 Assembly Manual preview
STARFLITE KT-390
Brand: Lafayette Pages: 51
Vaisala PTU200 Series User Manual preview
PTU200 Series
Brand: Vaisala Pages: 64
Campbell CS-3G Product Manual preview
CS-3G
Brand: Campbell Pages: 72
Newport zW Series Quick Start Manual preview
zW Series
Brand: Newport Pages: 16
Samson AirLine SYNTH Owner'S Manual preview
AirLine SYNTH
Brand: Samson Pages: 24

Brands by name

Popular brands

Load more brands