Altera Stratix II GX Page 384 User Manual Download

Page: 384 / 672

3–136

Altera Corporation

Stratix II GX Device Handbook, Volume 2

October 2007

Channel and Clock Multiplier Unit (CMU) PLL Reconfiguration

Section II — ALT2GXB_RECONFIG MegaWizard Instantiation

The following are the settings for the ALT2GXB_RECONFIG
MegaWizard:

■

Set the

What is the number of channels controlled by the reconfig

controller

option to

(This will provide separate

reconfig_from_gxb

ports for each instance).

■

Select the

Channel and TX PLL select/reconfig

option.

■

In the

Channel and TX PLL Reconfiguration

tab, select the

reconfig_address_out

reconfig_address_en

logical_tx_pll_sel

, and

logical_tx_pll_sel_en

ports so

that you can reuse the MIF. (Refer to

“How Many MIFs Do I

Require?” on page 3–132

Section III — Using the logical_tx_pll_sel During Reconfiguration

Follow the same procedure as mentioned in

“MIF Generation for Channel

and CMU PLL Reconfiguration” on page 3–111

to create your MIFs. In the

top-level design, assign the

Stratix II GX GXB TX PLL Reconfig group

setting

and assign the same reconfig group to the three channels.

If you would like to reconfigure CH0 to SONET/SDH OC48 mode, use
the following steps:

In the MegaWizard instantiation, set the logical tx pll value of the
main TXPLL for CH0 to

. The SONET/SDH OC48 MIF contains the

logical tx pll value of

. To use the SONET/SDH OC48 MIF for CH0,

set both the

logical_tx_pll_sel

and

logical_tx_pll_sel_en

ports to

in the reconfig controller.

what is the alternate PLL reference
clock index

0
You used a logical tx pll value of

for

SONET/SDH OC48. Therefore, the
alternate index (for FC-4G) should be
set to

protocol

BASIC

data rate

4.25 Gbps

clock frequency

106.25 MHz

Table 3–20. FC-2G Protocol Settings (Part 2 of 2)

Tab Page and Option

Setting

Summary of Contents for Stratix II GX

































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Stratix II GX

Reviews:

Related manuals for Stratix II GX

Brands by name

Popular brands

Altera Stratix II GX, User Manual

Search results

Summary of Contents for Stratix II GX

Reviews:

Related manuals for Stratix II GX

Brands by name

Popular brands