Altera Stratix II GX User Manual Download Page 204

Page: 204 / 672

2–192

Altera Corporation

Stratix II GX Device Handbook, Volume 2

October 2007

Native Modes

If successful byte ordering occurs without successful word alignment,
you should assert receive digital reset (

rx_digitalreset

) so that the

byte ordering block performs another round of byte ordering (one time
after asserting

rx_digitalreset

). This is only required when the byte

ordering block picks an incorrect byte order.

Figure 2–141. Byte Ordering Block Operation in OC-48

(OIF) CEI-PHY Interface Mode

The (OIF) CEI PHY Interface mode is intended to support two main
protocols:

■

Common Electrical I/O (CEI-6G) protocol defined by the Optical
Internetworking Forum (OIF) at data rates between 4.976 Gbps and
6.375 Gbps

■

Interlaken protocol at data rates between 3.135 Gbps and 6.375 Gbps

Stratix II GX transceivers support a data rate between 3.135 Gbps and
6.375 Gbps in (OIF) CEI PHY Interface Mode.

rx_dataout
(MSB)

rx_dataout
(LSB)

From Byte
Deserializer

rx_syncstatus

rx_byteorderalignstatus

To PLD core

rx_clkout

Pad

Byte
Ordering
Block

Summary of Contents for Stratix II GX

































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Stratix II GX

Reviews:

Related manuals for Stratix II GX

Brands by name

Popular brands

Altera Stratix II GX, User Manual

Search results

Summary of Contents for Stratix II GX

Reviews:

Related manuals for Stratix II GX

Brands by name

Popular brands