manualshive.com logo in svg

Altera Stratix II GX, User Manual

The Altera Stratix II GX User Manual is your essential guide to understanding and utilizing all the features of this powerful product. Easily accessible for download and free of charge at manualshive.com, this comprehensive manual empowers users to maximize the full potential of the Altera Stratix II GX.

Share
Download
background image

Altera Corporation 

  

3–145

October 2007

Stratix II GX Device Handbook, Volume 2

Stratix II GX Dynamic Reconfiguration

Figure 3–71. AEQ Write Timing Diagram for Power Down for a Single Channel (Logical Channel 4)

For more information about using the 

PMA controls

 option, refer to 

“Channel and PMA Controls Reconfiguration” on page 3–20

. The 

dynamic reconfiguration controller takes approximately 700 

reconfig_clk

 cycles to complete the write transaction with this option.

During the power down process, there may be bit errors on the receiver 
output data for a few receive parallel clock cycles. 

1

The ALT2GXB_RECONFIG translates the equalization values 
converged by the AEQ hardware and performs a rounding to 
the nearest manual equalization setting. 

Power Down for All Channels

This option provides the flexibility to power down the AEQ hardware in 
all the active channels connected to the same dynamic reconfiguration 
controller. The ALT2GXB_RECONFIG performs the translation as 
explained in 

“Power Down Options” on page 3–144

. The dynamic 

reconfiguration controller powers down the AEQ hardware on all the 
active channels starting with the lowest logical channel. For example, 
assume that you have three channels with logical address values of 

0

, 

4

, 

and 

8

, respectively. If only logical channels 

4

 and 

8

 have the AEQ feature 

enabled, when you use this option, the ALT2GXB_RECONFIG starts the 

xxxx

wrtie_all

reconfig_mode_sel[3:0]

busy

rx_eqctrl_out[19..16]

1001

ALT2GXB_RECONFIG indicates

that the AEQ hardware for logical  

channel address 4 is powered down

valid translated manual

equalization settings

read

0000

PMA read operation

4 (logical channel 4)

logical_channel_address[]

Summary of Contents for Stratix II GX

































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Stratix II GX

Labgear FV300 Instruction Manual preview
FV300
Brand: Labgear Pages: 14
Samsung DSR 3700 Instructions For Use Manual preview
DSR 3700
Brand: Samsung Pages: 19
Ramsey Electronics HR20 User Manual preview
HR20
Brand: Ramsey Electronics Pages: 28
GEOSUN gAirHawk Operation Manual preview
gAirHawk
Brand: GEOSUN Pages: 9
IFM Electronic Efector 800 VTV122 Operating Instructions preview
Efector 800 VTV122
Brand: IFM Electronic Pages: 5
Novus NP-430D Manual preview
NP-430D
Brand: Novus Pages: 2
JETStream jt270m User Manual preview
jt270m
Brand: JETStream Pages: 62
RF-Link ACS-5820 Quick Install Manual preview
ACS-5820
Brand: RF-Link Pages: 4
Icom IC-R6 Instruction Manual preview
IC-R6
Brand: Icom Pages: 40
Extron electronics XTP FR HD 4K Setup Manual preview
XTP FR HD 4K
Brand: Extron electronics Pages: 2
Strong SRT 8201 User Manual preview
SRT 8201
Brand: Strong Pages: 22
TV Star T2 505 User Manual preview
T2 505
Brand: TV Star Pages: 68
Hammarlund SP-600-JX-21 Service Instructions Manual preview
SP-600-JX-21
Brand: Hammarlund Pages: 70
Becker Centronic EasyControl EC415A-III Assembly And Operating Instructions Manual preview
Centronic EasyControl EC415A-III
Brand: Becker Pages: 20
Eddystone Broadcast XE150 Series Installation And Operation Manual preview
XE150 Series
Brand: Eddystone Broadcast Pages: 42
HBM DA2510 Quick Start Manual preview
DA2510
Brand: HBM Pages: 16
Polar Electro WearLink 31 User Manual preview
WearLink 31
Brand: Polar Electro Pages: 7
Technisonic Industries Limited TFM-566 Installation And Operating Instructions Manual preview
TFM-566
Brand: Technisonic Industries Limited Pages: 43

Brands by name

Popular brands

Load more brands