manualshive.com logo in svg

Altera Stratix II GX, User Manual

The Altera Stratix II GX User Manual is your essential guide to understanding and utilizing all the features of this powerful product. Easily accessible for download and free of charge at manualshive.com, this comprehensive manual empowers users to maximize the full potential of the Altera Stratix II GX.

Share
Download
background image

Altera Corporation 

  

3–131

October 2007

Stratix II GX Device Handbook, Volume 2

Stratix II GX Dynamic Reconfiguration

6.

Rename the generated MIFs to indicate the protocol for which the 
MIF is configured.

Section IV — Reset Control Logic and User Logic

The reset control logic takes care of resetting the transceiver during 
system initialization and during reconfiguration (Altera recommends a 
specific reset sequence, refer to 

“Reset Recommendations” on page 3–66

 

for more information).

For the user logic, use different clocks (

tx_clkout

 for GIGE protocol 

and 

rx_clkout

 for FC-4G and SONET/SDH OC48) for the parallel data 

in the receive interface of the ALT2GXB. The user logic is not discussed in 
this section. Refer to 

Figure 3–37 on page 3–82

 for more information 

regarding user logic in a similar configuration.

Section V — Top-Level Design and SRAM Object File (.sof) Generation

Follow these steps to generate a SRAM object file:

1.

Instantiate the six ALT2GXB channels in the top-level design. That 
is, stamp the FC-4G instance created for 

logical_tx_pll

 value 

0

 

three times for CH0, CH2, and CH4. 

2.

Similarly, stamp the instance created for 

logical_tx_pll

 value 

1

 

for CH1, CH3, and CH5. 

3.

Add the reset and user logic and connect the signals. In the 
assignment editor, use the 

Stratix II GX GXB TX PLL Reconfig 

group setting

 option and assign the 

tx_dataout

 of CH0 and CH1 

to the same reconfig group (this is required to assign CH0 and CH1 
to the same transceiver bank).

4.

Similarly, assign the same reconfig groups for CH2-CH3 and 
CH4-CH5.

Case II: Configuring Transceiver Channels to Switch Independently 
Between Three Different Protocols

This example discusses the steps to reconfigure the three full-duplex 
channels (CH0, CH1, and CH2) in a transceiver bank between the FC-4G, 
FC-2G, GIGE, SONET/SDH OC48 protocols. In the previous example, 
the design used only two channels in a transceiver bank. Therefore, each 
channel could use a dedicated TX PLL. 

Summary of Contents for Stratix II GX

































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Stratix II GX

Garod Radio 900 Series Service Manual preview
900 Series
Brand: Garod Radio Pages: 29
Samsung TV Quick Manual preview
TV
Brand: Samsung Pages: 10
Garmin ECHOMAP Ultra Series Installation Instructions preview
ECHOMAP Ultra Series
Brand: Garmin Pages: 4
Nautel VX150 Manual preview
VX150
Brand: Nautel Pages: 105
Teac HD-1 Owner'S Manual preview
HD-1
Brand: Teac Pages: 20
Vega T-25 Owner'S Manual preview
T-25
Brand: Vega Pages: 12
IRiver AFT-100-H10 Manual preview
AFT-100-H10
Brand: IRiver Pages: 2
M-system Mini-M M2TG Instruction Manual preview
Mini-M M2TG
Brand: M-system Pages: 3
YBA DESIGN YA701 User Manual preview
YA701
Brand: YBA DESIGN Pages: 54
Vaisala Drycap DMT142 User Manual preview
Drycap DMT142
Brand: Vaisala Pages: 50
Yaesu FT-250E Manual preview
FT-250E
Brand: Yaesu Pages: 44
Easy wave RCJ02 Quick Start Manual preview
RCJ02
Brand: Easy wave Pages: 8
Strong SRT 4356 PVR Evolution User Manual preview
SRT 4356 PVR Evolution
Brand: Strong Pages: 74
Japan Radio Co. NCR-330 Instruction Manual preview
NCR-330
Brand: Japan Radio Co. Pages: 75
Kanga Products Bassinet Manual And User Manual preview
Bassinet
Brand: Kanga Products Pages: 26
zisa PS-2x6 User Manual preview
PS-2x6
Brand: zisa Pages: 11
Radio Systems i.AM.Radio Transmitter Installation And Operation Manual preview
i.AM.Radio Transmitter
Brand: Radio Systems Pages: 12
Target HF3 User Manual preview
HF3
Brand: Target Pages: 17

Brands by name

Popular brands

Load more brands