ABB ACS280 Firmware Manual Download Page 280

Page: 280 / 430

280 Parameters

97 Motor control

Switching frequency; slip gain; voltage reserve; flux

braking; anti-cogging (signal injection); IR

compensation.

97.01

Switching frequency

reference

Defines the switching frequency of the drive that is

used as long as the drive does not heat too much. See

section

Switching frequency

on page

Higher switching frequency results in lower acoustic

noise.
In multimotor systems, do not change the switching

frequency from the default value.

4 kHz

4 kHz.

8 kHz

8 kHz.

12 kHz

12 kHz.

97.02

Minimum switching

frequency

Lowest switching frequency that is allowed. Depends

on the frame size.

1.5 kHz

1.5 kHz. In some larger frame sizes 1 kHz is used

instead.

1.5

2 kHz

2 kHz.

4 kHz

4 kHz.

8 kHz

8 kHz.

12 kHz

12 kHz.

97.03

Slip gain

Defines the slip gain which is used to improve the

estimated motor slip. 100% means full slip gain; 0%

means no slip gain. The default value is 100%. Other

values can be used if a static speed error is detected

despite having the setting at full slip gain.

Example

(with nominal load and nominal slip of 40

rpm): A 1000 rpm constant speed reference is given

to the drive. Despite having full slip gain (= 100%),

a manual tachometer measurement from the motor

axis gives a speed value of 998 rpm. The static speed

error is 1000 rpm - 998 rpm = 2 rpm. To compensate

the error, the slip gain should be increased to 105% (2

rpm / 40 rpm = 5%).

100%

0…200%

Slip gain.

1 = 1%

No.

Name/Value

Description

Default
FbEq 16

Summary of Contents for ACS280














































































































































































































































































































































































































































Search results

Summary of Contents for ACS280

Reviews:

ABB ACS280, Firmware Manual, Page: 280 / 430

Search results

Summary of Contents for ACS280

Reviews: