manualshive.com logo in svg

Renesas SH7763, Руководство по оборудованию

Желаете загрузить бесплатное Руководство по аппаратному обеспечению для Renesas SH7763? Вам нужно посетить {сайт} и скачать это руководство прямо сейчас! Наше руководство поможет вам лучше понять функционал этого продукта и настроить его для своих потребностей.

Поделиться
Скачать
background image

Section 13   PCI Controller (PCIC) 

 

 

Rev. 1.00  Oct. 01, 2007  Page 547 of 1956 

 

 REJ09B0256-0100 

31 30

24 23

16 15

11 10

8 7

2 1

0

31

11 10

16 15

8 7

2 1

0

Configuration
address register
(PCIPAR)

CCIE

Reserved

BN

DN

FN

CRA

 Only one '1'

00000

00

00

PCI local bus
address
(AD31 to AD0)

 

Figure 13.15   Address Generation for Type 0 Configuration Access 

In configuration accesses, a PCI master abort (no device connected) will not cause an interrupt. 

Configuration writes will end normally. Configuration reads will return a value of 0. 

(3)  Special Cycle Generation 

When the PCIC operates as the host device, a special cycle is generated by setting H'8000 FF00 in 
the PCIPAR and writing to the PCIPDR. 

(4) Arbitration 

In host bus bridge mode, the PCI bus arbiter in the PCIC is activated. 

The PCIC supports four external masters (i.e., four REQ and GNT pairs). 

If use of the bus is simultaneously requested by more than one device, the bus is granted to the 
device with the highest priority. 

The PCI bus arbiter supports two modes to determine the priority of devices: fixed priority and 
pseudo-round-robin. The mode is selected by the BMAM bit in PCICR. 

Fixed Priority: 

When the BMAM bit in PCICR is cleared to 0, the priorities of devices are fixed 

the following default values. 

PCIC > device 0 > device 1 > device 2 > device 3 

The PCIC always gains use of the bus over other devices. 

Pseudo-Round-Robin: 

When the BMAM bit in PCICR is set to 1, the most recently granted 

device is assigned the lowest priority. 

The initial priority is the same as the fixed priority mode. 

Содержание SH7763











































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SH7763

IEI Technology PCIE-Q470 Quick Installation Manual preview
PCIE-Q470
Бренд: IEI Technology Страницы: 19
IEI Technology KINO-DH420 User Manual preview
KINO-DH420
Бренд: IEI Technology Страницы: 87
IEI Technology HPE-4S2 Quick Installation Manual preview
HPE-4S2
Бренд: IEI Technology Страницы: 3
Jetter JXM-IO-E30 Installation Manual preview
JXM-IO-E30
Бренд: Jetter Страницы: 35
Raritan DOMINION SX - Quick Setup Manual preview
DOMINION SX -
Бренд: Raritan Страницы: 4
Lanner NCA-2510 Installation Manual preview
NCA-2510
Бренд: Lanner Страницы: 2
Opvimus UMX-ETH+ Operating Instructions Manual preview
UMX-ETH+
Бренд: Opvimus Страницы: 12
WHOOP WHT-25LT Quick Start Manual preview
WHT-25LT
Бренд: WHOOP Страницы: 26
Datasat DDR-16 AES67 Installation And Operating Manual preview
DDR-16 AES67
Бренд: Datasat Страницы: 24
Delta Electronics Through Hole Power Inductors 1411 Product Specifications preview
Through Hole Power Inductors 1411
Бренд: Delta Electronics Страницы: 1
Kramer RK-10MT Quick Start Manual preview
RK-10MT
Бренд: Kramer Страницы: 2
SafeHome NVR903 Manual preview
NVR903
Бренд: SafeHome Страницы: 24
Omron NJ501-1300 User Manual preview
NJ501-1300
Бренд: Omron Страницы: 432
Lantronix N-FXE 02B Series User Manual preview
N-FXE 02B Series
Бренд: Lantronix Страницы: 10
Lindy Modular Fast Fiber Switch Converter MT-RJ Specifications preview
Modular Fast Fiber Switch Converter MT-RJ
Бренд: Lindy Страницы: 3
Terasic Cypress CapSense P0080 User Manual preview
Cypress CapSense P0080
Бренд: Terasic Страницы: 22
ekwb 3831109810316 User Manual preview
3831109810316
Бренд: ekwb Страницы: 16
Infoblox ND-2200 Installation Manual preview
ND-2200
Бренд: Infoblox Страницы: 44

Бренды по названию

Популярные бренды

Загрузить еще бренды