Foma F903i' 06.10, Руководство пользователя

Страница: 556 / 567

55
AT&F The AT command settings in the FOMA terminal are reset to the default.
When this command is executed during communication, the terminal is reset after the line
is disconnected (displaying "NO CARRIER").
AT&F
OK (When in offline mode)
AT&S<n>
*1
Sets control of the data set ready (DR) signal to be output to DTE.
n=0 : Always ON (default)
n=1 : ON at time of connection
AT&S0
OK
AT&W Register the current settings in the FOMA terminal.
AT&W
OK
AT
＊
DANTE Indicates FOMA terminal reception level in the "
＊
DANTE : <n>" format.
n=0 :
圏外
(out of service area)
n=1 : Received signal level of the FOMA terminal is 0 or 1 antenna.
n=2 : Received signal level of the FOMA terminal is 2 antennas.
n=3 : Received signal level of the FOMA terminal is 3 antennas.
AT
＊
DANTE=? : Displays a list of displayable values
AT ＊ DANTE
＊ DANTE : 3
OK
AT ＊ DGANSM=<n>
*2
Sets to reject or permit incoming packet communications.
n=0 : Reject setting = OFF, Accept setting = OFF (default)
n=1 : Reject setting=ON
n=2 : Accept setting=ON
AT ＊ DGANSM? : Displays current settings
AT ＊ DGANSM=? : Displays a list of assignable values
AT
＊
DGANSM=0
OK
AT
＊
DGAPL=<n> [,<cid>]
*2
Sets the dialup connections (APN) to permit incoming packet communications. APN uses
<cid> defined by +CGDCONT command.
n=0 : Adds to list of APN permitted for incoming communications
n=1 : Deletes from list of APN permitted for incoming communications
If the <cid> is not defined by the +CGDCONT command, it can still be added to or deleted
from the list.
If the <cid> is omitted, all the <cid> are added to/deleted from the list.
AT
＊
DGAPL? : Displays current settings
AT
＊
DGAPL=? : Displays a list of assignable values
AT ＊ DGAPL=0,1
OK
AT ＊ DGARL=<n> [,<cid>]
*2
Sets the dialup connections (APN) to refuse incoming packet communications. APN uses
<cid> defined by +CGDCONT command.
n=0 : Adds to list of APN rejected for incoming communications
n=1 : Deletes from list of APN rejected for incoming communications
If the <cid> is not defined by the +CGDCONT command, it can still be added to or deleted
from the list.
If the <cid> is omitted, all the <cid> are added to/deleted from the list.
AT
＊ DGARL? : Displays current settings
AT ＊ DGARL=? : Displays a list of assignable values
AT
＊
DGARL=0,1
OK
AT
＊
DGPIR=<n>
*2
Sets whether to send caller ID when packet communication connection is being
established. This command is available when a communication is sent or received.
n=0 : Connects to APN directly (default)
n=1 : Connects to APN prefixing 184
n=2 : Connects to APN prefixing 186
When Show/Hide caller ID is specified by dialup network
→
P40
AT
＊
DGPIR? : Displays current settings
AT
＊
DGPIR=? : Displays a list of assignable values
AT ＊ DGPIR=0
OK
AT ＊ DRPW Indicates an index for the reception power of the radio signals that FOMA terminal receive
in the "
＊ DRPW : <n>" format.
AT ＊ DRPW=? : Displays a list of displayable values
AT
＊
DRPW
＊
DRPW : 0
OK
AT+CEER Displays reason for disconnection of immediately preceding communication.
Disconnection reason list
→ P58
AT+CEER
+CEER:36
OK
AT+CGDCONT
*2
Sets dialup connection (APN) for packet communication. → P58
AT+CGDCONT? : Displays current settings
AT+CGDCONT=? : Displays a list of assignable values
AT+CGDCONT=2,"ppp",
"abc"
OK
Upper slot: Command
Lower slot: Example
Description