Toshiba TX49 TMPR4937 Manual Download | Manualshive

Page: 230 / 553

background image

Chapter 9 SDRAM Controller

9-14

9.3.10.2 ECC Error Notification

When either an ECC error or a parity error occurs, error data is written into one of the following

fields, then error notification is performed as described below:

•

Error Address Field (ERRAD) in the ECC Status Register (ECCSR)

•

Error ECC/Parity Mode Field (ERRMODE)

•

Error Memory Width Field (ERRMW)

•

Error Syndrome Field (ERRS)

The Multi-bit Error bit (ECCSR.MBERR) of the ECC Status Register is set and an interrupt is

generated if either an ECC multi-bit error or parity error is detected during any Read/Write access
while the Multi-bit Error Interrupt Enable bit (ECCCR.MEI) is set.

The Single-bit Error bit (ECCSR.SBERR) of the ECC Status Register is set and an interrupt is

generated if an ECC single-bit error is detected during any Read/Write access while the Single-bit
Error Interrupt Enable bit (ECCCR.SEI) is set.

Multi-bit errors are assigned a higher priority than single-bit errors. If a multi-bit error is

detected while the Single-bit Error bit (ECCSR.SBERR) is set, then the Single-bit Error bit
(ECCSR.SBERR) is cleared, error data is written for the multi-bit error, then error notification is
performed. If a single-bit error is detected while the Multi-bit Error bit (ECCSR.MBERR) is set,
the Single-bit Error bit (ECCSR.SBERR) is not set and not error data is written. However, the
single-bit error is corrected according to the usual procedure.

The following error notification will also be performed if either an ECC multi-bit error or parity

error is detected while the Multi-bit Error Bus Error Enable Bit (ECCCR.MEB) of the ECC
Control Register is set.

During read access by the TX49 core, bus error notification is sent to the TX49 core and an

exception is generated. A nonmaskable interrupt is generated during Read-Modify-Write memory
Read access that is performed when writing from the TX49 core data that is smaller than 64 bits.
Bus error notification is sent to the appropriate bus master during Read/Write access from another
bus master.

«
...
228
229
230
231
232
...
»

Summary of Contents for TX49 TMPR4937










































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for TX49 TMPR4937

Pixie-4 Express

Brand: XIA Pages: 17

Brand: Zenith Data Systems Pages: 64

Brand: Ubiquiti Pages: 23

Brand: FOR-A Pages: 39

Brand: Zoom Pages: 48

Procont LMC-008-IO

Brand: janitza Pages: 28

ELITENAS EN104L+(B)

Brand: Sans Digital Pages: 9

Brand: ICP Pages: 68

Brand: Icy Box Pages: 2

Brand: PairGain Pages: 80

Brand: A.E.B. Pages: 28

Brand: ExtraHop Pages: 3

DUAL Nx56/64 1200142L1#

Brand: ADTRAN Pages: 48

CG9103-2RS232-1USB

Brand: BiPOM Electronics Pages: 8

Brand: PairGain Pages: 48

Brand: XtendLan Pages: 17

SNMP-1000-E2B1E

Brand: Advantech Pages: 4

Brand: Omron Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands