Toshiba TX49 TMPR4937 Manual Download | Manualshive

Page: 535 / 553

background image

Chapter 23 Notes on Use of TMPR4937

23-5

– Only one channel performs single transfer

(1) Single transfer performed with only one channel

Perform either (a) or (b) to prevent a malfunction.

(2) Single transfer performed with one channel and burst transfer

Perform (b) to prevent a malfunction.

– Two or more channels perform single transfer

(3) Single transfer (performed with two to four channels)

Perform (a) to prevent a malfunction.

(4) Single transfer performed with two to three channels and burst transfer

Perform (a) to prevent a malfunction. For the channel used for burst transfer, set the same offset to
DMSARn and DMDARn, or set 1 to DMCCRn.USEXFSZ. (Set the on-chip FIFO to be shared
with multiple DMA channels by which no data remains in FIFO.)

In dual address burst transfer, when 0 is set to the transfer size mode bit and the offset value is
different between source address and destination address, data may remain in FIFO. (See 8.3.8.2
Burst Transfer During Dual address Transfer.) When a bus error occurs during single transfer for
which workaround (a) is performed, data is erased if it remains in FIFO during burst transfer. This
occurs because FIFO is reset due to a bus error. Since DMAC does not detect data erasing, you
need to set FIFO to contain no data.

«
...
533
534
535
536
537
...
»

Summary of Contents for TX49 TMPR4937










































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for TX49 TMPR4937

SmartMedia Adapter PC Card REX-SMA01F

Brand: Ratoc Systems Pages: 75

Brand: Q-See Pages: 2

PARTNER Voice Messaging PC Card Release 2

Brand: Lucent Technologies Pages: 67

FieldPoint cFP-RTD-122

Brand: National Instruments Pages: 15

PCI-6110E/6111E

Brand: National Instruments Pages: 113

OP-8000-EDFA-1U Series

Brand: Optostar Pages: 9

Brand: ADTRAN Pages: 2

CNPS7000A Series

Brand: ZALMAN Pages: 9

Brand: Atmel Pages: 2

Brand: ebm-papst Pages: 13

Brand: MSNswitch Pages: 2

Brand: Promise Technology Pages: 26

Brand: XtendLan Pages: 21

Brand: Ariesys Pages: 10

Brand: JETWAY Pages: 47

LITTLE BOARD P5X

Brand: Ampro Corporation Pages: 121

Brand: Planet Pages: 20

Brand: Vista Pages: 93

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands