Strata CIX 200 Programming Manual Download Page 287 | Manualshive

Page: 287 / 508

background image

Trunks

ISDN

Strata CIX Programming Vol.1 12/09

6-33

T

runks

20 B Ch Selection Method

The method used for selecting an idle ‘B’ channel and the reaction if the PSTN
indicates the channel is not available needs to be chosen to originate a call from
CIX.

Possible values:Explicit (default), Preferred or Any Channel

Preferred option is recommended unless PSTN needs other choice.

21 B-Ch Selection

The search method for choosing an idle ‘B’ channel shall also be specified.
Backward Terminal is the normal method with the PSTN following a Forward
Terminal method.

Possible values:Forward Cyclic, Backward Cyclic, Forward Terminal or

Backward Terminal (default)

22 T1 Time Slot Pattern

1544 Time Slot Pattern.

Possible values:Fixed1 (default), Flexible or Floating

23 E1 Time Slot Pattern

2048 Time Slot Pattern

Possible values:Fixed1 (default), Fixed2 or Flexible

24 T-Wait Timer

Specify whether the T-Wait timer is to be enabled or disabled. This field is only
valid for Nat’l ISDN. This should not be enabled for PRI, it is only for BRI.

Possible values:Enable or Disable (default)

25 RBT on Incoming Call

Enable Ringback Tone when terminating a call. This field is only valid for Nat’l
ISDN.

Possible values:Enable or Disable (default)

26 Network Mode

Set this span as Master or Slave for Layer 2 of a Strata Net PRI. The opposite
value must be set for the node in which this Strata Net PRI terminates. This
governs call setup activity and is not related to clock synchronization.

Possible values:Master (default) or Slave

27 Negotiation Priority

Sets this span as Side A or Side B for Layer 3 of a Strata Net PRI. The opposite
value must be set for the node in which this Strata Net PRI terminates.

Possible values:Side A (default) or Side B

28 Layer 1 short break

tolerant

If layer 1 is interrupted for less than 90 seconds CIX will keep the current calls
open.

Possible values:Enable (default) or Disable

29 2-B channel Transfer

Enable this option to allow 2-B channel conference on PRI calls. This allows two
PRI channels to be connected in the same Conference or Tandem call.

Note

This option must also be enabled by PRI provider to allow it to
work.

30 Q931 Protocol Timer

Sets the Q931 Protocol Timer. If Long is set, T303 is 8s and T301 is 300s.

31 Send Malicious Call ID

F

IELD

D

ESCRIPTION

«
...
285
286
287
288
289
...
»

Summary of Contents for CIX 200





























































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for CIX 200

Brand: 3Com Pages: 118

CoreBuilder 3500

Brand: 3Com Pages: 92

Brand: Krüger & Matz Pages: 20

Brand: Allview Pages: 142

Brand: Wafer Microelectronics Pages: 6

Brand: Docomo Pages: 596

Brand: X-View Pages: 42

Brand: C.R. Laurence Pages: 2

Sprint Torcque XT

Brand: Kyocera Pages: 209

Orion Mini S350

Brand: Posh Pages: 20

Brand: KDDI Pages: 51

Brand: Audiovox Pages: 49

Brand: Docomo Pages: 162

MQ03-LTE-M-FIRE

Brand: M2M Pages: 11

Brand: Samsung Pages: 209

Brand: Samsung Pages: 355

Brand: Samsung Pages: 189

Brand: Xiaomi Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands