Strata CIX 200 Programming Manual Download Page 151 | Manualshive

Page: 151 / 508

background image

Licenses - SYSTEM, MAS, ACD

ACD Dongle

Strata CIX Programming Vol.1 12/09

3-43

CTI-TMENT-SOA

OAISYS Talkument Small Office Analog System.
OAISYS Talkument Voice Documentation System includes PC, cards and software, equipped for 8 analog CO
interfaces or 20 IP end points with unlimited users. Includes one year warranty. Monitor sold separately. Requires
LIC-ACD if ACD or Net Phone is not installed. VoIP requires a LAN switch with port mirroring to capture the audio
stream of all IP phones. Additional switches with port mirroring may be needed if phones are connected to different
networks. (The license activation code will be sent by the 3rd party vendor to the e-mail address provided to
Toshiba by the dealer at time of order entry in FYI).

CTI-TMENT-SOF

OAISYS Talkument Small Office System.
OAISYS Talkument Voice Documentation System includes PC, cards and software, equipped for 20 IP end points
with unlimited users. Includes one year warranty. Monitor sold separately. Requires LIC-ACD if ACD or Net Phone
is not installed. VoIP requires a LAN switch with port mirroring to capture the audio stream of all IP phones.
Additional switches with port mirroring may be needed if phones are connected to different networks. (The license
activation code will be sent by the 3rd party vendor to the e-mail address provided to Toshiba by the dealer at time
of order entry in FYI).

CTI-TMENT-SUPG

OAISYS Talkument Small Office Upgrade.
Upgrade for OAISYS Talkument Small Office System to increase from 20 IP end points to 48 IP end points.
Includes one year warranty. Monitor sold separately. (The license activation code will be sent by the 3rd party
vendor to the e-mail address provided to Toshiba by the dealer at time of order entry in FYI).

CTI-TMENT-SYS

OAISYS Talkument system.
OAISYS Talkument Voice Documentation System includes PC, cards and software, equipped for 2T1/PRI
interfaces or 48 IP end points with unlimited users. Includes one year warranty. Monitor sold separately. Requires
LIC-ACD if ACD or Net Phone is not installed. VoIP requires a LAN switch with port mirroring to capture the audio
stream of all IP phones. Additional switches with port mirroring may be needed if phones are connected to different
networks. (The license activation code will be sent by the 3rd party vendor to the e-mail address provided to
Toshiba by the dealer at time of order entry in FYI).

CTI-TRACER-16P

Tracer 16 port voice board. 16 port analog voice board.

CTI-TRACER-16S

Tracer 16 port station board. 16 port digital station board

CTI-TRACER-24A

Tracer 24 port voice board. 24 port analog voice board.

CTI-TRACER-24P

Tracer single T1/PRI voice board. Single T1 or PRI voice board.

CTI-TRACER-24S

Tracer 24 port station board. 24 port digital station board

CTI-TRACER-48P

Tracer dual T1/PRI voice board. Dual T1 or PRI voice board.

«
...
149
150
151
152
153
...
»

Summary of Contents for CIX 200





























































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for CIX 200

Brand: Uniden Pages: 16

Brand: Haier Pages: 57

Brand: UMX Pages: 56

Brand: Yealink Pages: 361

Brand: Yealink Pages: 7

Brand: Yealink Pages: 4

Brand: Yealink Pages: 2

Brand: Yealink Pages: 7

Brand: EMPORIA Pages: 40

Brand: Ecom Instruments Pages: 64

Brand: Talkswitch Pages: 83

Brand: Catchwell Pages: 101

OneTouch X1 7053D

Brand: Alcatel Pages: 20

Brand: Blackberry Pages: 6

Brand: SoftBank Pages: 36

Brand: INQ Pages: 101

Brand: Hisense Pages: 33

Brand: Med-Pat Pages: 37

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands