Strata CIX 200 Programming Manual Download Page 250

Page: 250 / 508

Station

Assignment

5-46

Strata CIX Programming Vol.1 12/09

217 ISDN Station Data

Prerequisite Program:

202

page 5-42

Set ISDN Station parameters to define ISDN capabilities.

1. Select Station > ISDN Station Data.

2. Enter a Primary DN

for an existing record or click one of the following buttons:

•

List

– view a summary list of programmed Hunt Groups.

•

Copy

– Enter a DN in the Primary DN field and click

Copy

to make a new DN assignment with BRI

Station settings copied from the DN entered in the Primary DN field.

•

Get Default

- Sets all data to factory defaults.

3. Set up ISDN Station Data using the Program Detail table below.

4. Click

Submit

Table 5-6

BRI Bearer Capability of ISDN

Bearer Services

Bellcore Nat’l ISDN

ETSI

TTC

Circuit
Mode

Speech

3.1kHz Audio

7kHz Audio

Unrestricted Digital
Information

64 kbps

Rate adaptation from 56
kbps

2x64

IELD

ESCRIPTION

Primary DN

Enter Primary DN.

Possible values:Up to 5 digits (default = no value)

01 Station LCD Name

Enter the name that should be displayed on telephone LCDs for this PDN. (Max.
8 characters with R1.0~R2.20; Max.16 characters with R2.21 and above.

Possible values:Up to 9 ASCII characters (default = no value)

02 Dial Method

Select the audible tone when dialing.

Possible values:Dial Tone (default), Entry Tone or No Tone

03 System Call Forward

Select the System Call Forward assignment for this station.

Possible values:0~4 (CIX100), 0~10 (CIX200, CIX670/1200 Basic),

0~32 (CIX670 Exp), 0~48 (CIX1200 Exp) (default = 0)

04 CF Password

Protect the System Call Forward settings by creating a password.

Possible values:Up to 4 digits (default = no value)

05 Door Phone Override

DND

Enable the Door Phone ringing indicator to override Do Not Disturb.

Possible values:Enable or Disable (default = Disable)

Summary of Contents for CIX 200





























































































































































































































































































































































































































































































































Search results

Summary of Contents for CIX 200

Reviews:

Related manuals for CIX 200

Brands by name

Popular brands

Strata CIX 200, Programming Manual

Search results

Summary of Contents for CIX 200

Reviews:

Related manuals for CIX 200

Brands by name

Popular brands