Strata CIX 200 Programming Manual Download Page 272 | Manualshive

Page: 272 / 508

background image

Trunks

6-18

Strata CIX Programming Vol.1 12/09

Data Day1 Destination
Data Day2 Destination
Data Night Destination

Enter the Destination Directory Number or Access Code.

Possible values:Up to 32 digits (default = no value)

If Dialing Digits is the Destination Type enter the Directory Number that the line
should ring. If the line should ring over external page, enter #31xx, where xx is the
external page group number. If the default page access code #31 was changed, use
the new page access code as the leading digits.

Line access codes and network routing numbers can also be entered to route
incoming calls back out to a public or private network number.

11 DID/DNIS No. VMID

Enter the VM mailbox number which should answer calls for this DID/DNIS number.

Possible values:Up to 10 digits (default = no value)

•

This code is only sent if using SMDI VM integration in Program 580, 01. This code
is replaced after voice mail answers by the DTMF code set in Program 309, 15
DID/DNIS DTMF VMID code - if programmed. Therefore, if using Program 309,
15 code, this VMID code is not necessary.

This mailbox number is sent to voice mail on a DID/DNIS call that rings directly to
voice mail and on a direct DID/DNIS call to a DN that forwards to voice mail before it
is answered by the DN.

If a DID/DNIS call is answered by a station and then transferred to a DN that
forwards to voice mail, this mailbox number of the DID/DNIS number or the
forwarding DN's mailbox number will be sent to voice mail per Program 579, 01.

If this VMID code is not set, direct DID/DNIS calls will go to the VM general greeting
and DID/DNIS calls that forward from a DN to VM will go to the DN's VMID mailbox.

This Voice Mailbox number is added to SMDI packets direct and forwarded
DID\DNIS calls to voice mail as explained above.

12 DID/DNIS Name

Enter DNIS name. Names are assigned from eManager (not programming phones).

Possible values:Up to 16 ASCII characters (default = no value)

15 VM Application

Digits

Enter the VM mailbox number which should answer calls for this DID/DNIS number.

Possible values:Digits 0~9,

*

and #. For a pause enter Px, where x=0~9 (seconds),

up to 10 characters (default = no value).

This mailbox number will be sent to voice mail on a DID/DNIS call that rings directly
to voice mail and on a direct DID/DNIS call to a DN that forwards to voice mail before
it is answered by the DN.

If a DID/DNIS call is answered by a station and then transferred to a DN that
forwards to voice mail, this mailbox number of the DID/DNIS number or the
forwarding DN's mailbox number will be sent to voice mail per Program 579, 01.

If this VMID code is not set, direct DID/DNIS calls will go to the VM general greeting
and DID/DNIS calls that forward from a DN to VM will go to the DN's VMID mailbox.
This voice mailbox number is sent to the VM port as DTMF digits after the VM port
answers a DID/DNIS call as explained above. These digits are sent to the VM port if
the CIX is set for SMDI or DTMF integration in Program 580, 01.

16 Tenant Number

Enter the Tenant number to which this DID number should be assigned.

Possible values:1(default)~8.

F

IELD

D

ESCRIPTION

«
...
270
271
272
273
274
...
»

Summary of Contents for CIX 200





























































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for CIX 200

Brand: Samsung Pages: 170

Yealink SIP-T20P

Brand: Yealink Pages: 2

Brand: Alcatel Pages: 52

IP Vision Dialog 4425

Brand: Ericsson Pages: 136

Brand: Sony Ericsson Pages: 89

Brand: Fortinet Pages: 28

Brand: Sagem Pages: 64

Brand: 2N Pages: 180

Brand: HTC Pages: 204

Brand: Alcatel Pages: 2

Brand: Xiaomi Pages: 8

Brand: IPRO Pages: 23

Brand: Geemarc Pages: 47

Brand: Geemarc Pages: 72

Brand: QUO Pages: 9

Brand: Zte Pages: 60

Brand: Cisco Pages: 37

Brand: Blu Pages: 9

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands