Strata CIX 200 Programming Manual Download Page 209 | Manualshive

Page: 209 / 508

background image

Station

Assignment

Strata CIX Programming Vol.1 12/09

5-5

St
a

tio

n

19 VMID Code

Enter the voice mailbox number that should answer calls when this PDN calls
voice mail, or when this PDN is called and then forwards to voice mail (this
number is prefixed by codes in Prog 579, 11~16).

Valid entries: digits 0~9, * and #, maximum 10 characters.

This VMID code is sent to the voice mail device in SMDI packets or DTMF
tones on direct calls to voice mail from the PDN and on calls to the PDN that
forward to voice mail.

Note: see Prog. 580 for SMDI or DTMF choice.

Possible values:1 ~ 10 digits (default = no data)

20 VM MW Center Port

Message Waiting Center DN.

Enter the VM PDN or Pilot DN number that should display on telephone LCDs
when calling Voice Mail or receiving calls from Voice mail.

Possible values:Valid DN (default = no data)

21 Travel COS Change

Privilege Change the Traveling Class of Service Override Code.

Possible values:Enabled or Disabled (default = Disabled)

22 TGAC Override

Trunk Group Access Code Override for Attendant console.

Possible values:Enabled or Disabled (default = Disabled)

23 Service Tones

Disable Services Tone for Data Privacy. Service tone, such a Call Waiting
Tone, should be disabled for modems, FAX machines, and similar devices.

Possible values:Enabled or Disabled (default = Enabled)

24 Call Waiting Tone

Enable/Disable the station to receive call waiting (camp-on) and ring over busy
(rob) tone.

CW tone is always two beeps.

ROB tone can be two beeps or continuous as set in PRG 204, 27.

Possible values:Enabled or Disabled (default = Enabled)

25 Dial Directory

Privilege to put the user name in the list display of large LCD (Directory
Assistance)

Possible values:Enabled or Disabled (default = Enabled)

26 Door Over DND

Enable DND to be overridden by a door phone.

Possible values:Override or Not Override (default = Not Override)

27 Set System Speed Dial

Privilege to set System Speed Dial numbers.

Possible values:Enabled or Disabled (default = Disabled)

28 Network COS

Network Class Of Service number.

Possible values:1~ 32 (default = 1)

29 Auto OCA

OCA occurs automatically when making a call to a busy station that allows
OCA calls to be received.

Possible values:Enabled or Disabled (default = Enabled)

Table 5-1

Station Assignment Data for IP, and SIP Telephones (Prog 260) (continued)

«
...
207
208
209
210
211
...
»

Summary of Contents for CIX 200





























































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for CIX 200

Galaxy XCover FieldPro

Brand: Samsung Pages: 14

Brand: Samsung Pages: 55

Galaxy Z Flip 5G

Brand: Samsung Pages: 2

Brand: Samsung Pages: 184

Brand: Samsung Pages: 2

Brand: Samsung Pages: 9

Brand: Samsung Pages: 25

Brand: Samsung Pages: 16

Brand: TCL Pages: 35

Brand: Pantech Pages: 126

Brand: 101VOICE Pages: 2

Brand: Yealink Pages: 6

Brand: Yealink Pages: 8

Intercept SPH-M810

Brand: Samsung Pages: 235

Brand: Tadiran Telecom Pages: 253

Brand: KDDI Pages: 63

Brand: M4 Pages: 22

Sphere AAP553G-315

Brand: Bauhn Pages: 40

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands