Strata CIX 200 Programming Manual Download Page 303

Page: 303 / 508

Trunks

Trunk DID/DNIS Setup Wizard

Strata CIX Programming Vol.1 12/09

6-49

runks

326 SIP Trunk Assignment

Prerequisite Program:

100; 304; 309; 306

This command assigns SIP trunks.

1. Select IP-Telephony > SIP Trunking - Channel Group Setting tab.

2. Setup the SIP Channel Group by adding values to the remaining fields.

List

- View a list of the programmed SIP Trunk Channel Groups.

Get Default

- restores data to factory defaults.

5. Click

Submit

IELD

ESCRIPTION

00 SIP Trunk Channel

Group

Enter a channel group number.

Possible values:1~32 (CIX40), 1~32 (CTX100), 1~48 (CTX670 Basic &

CIX200), 1~128 (CTX670 Exp), 1~ 48 (CIX1200 HCTU only),
1~128 (CIX1200 HCTU+HEXAU), 1~220 (CIX1200 HCTU
+HEXBU)

01 Equipment

Assign the Equipment Number of the LIPU/LIPS MIPU and/or GIPx card.

CIX40 GIPx/MIPU card in R1 CHSU40A Cabinet is 01/Slot 06 (0106).

CIX40 GIPx/MIPU card in R2 CHSU40A2 Cabinet is 01/Slot 05 (0105).

Cabinet numbers:

•

CTX100: Select 01 for Base and Expansion cabinet.

•

CTX670: Select 01 for Base and 02 ~ 07 respectively for each
Expansion cabinet.

•

CIX200: Select 01 for Base and 02 for Expansion cabinet.

•

CIX1200: Select 01 for Base and 02 ~ 12 respectively for each
Expansion cabinet.

Slot numbers:

•

CIX100: Select 01 or 03 for Base slots and 05 or 07 for Expansion
slots

•

CIX200: Select 01 ~ 04 for either cabinet.

•

CIX670: Select 01, 03, 05 and 07 for Base slots and 01, 03 and 05
for Expansion slots.

•

CIX1200: Select 01, 03, 05 and 07 for Base slots and 01, 03 and
05 for Expansion slots.

02 LAN Interface Number

There is only one LAN interface on an MIPU/GIPU.

Possible values:1

03SIP Trunk Channels

Enter the number of GIPU, MIPU, LIPU or LIPS channels to be assigned as
SIP trunk resources

Possible values:(GIPU) 1 ~ 8, (MIPU16, LIPU, LIPS) 1 ~ 16, (MIPU24) 1 ~ 32

04 RBT on Incoming Call

Enable ringback tone to be returned to the caller.

Possible values:Enable (Default) or Disable

Summary of Contents for CIX 200





























































































































































































































































































































































































































































































































Search results

Summary of Contents for CIX 200

Reviews:

Related manuals for CIX 200

Brands by name

Popular brands

Strata CIX 200, Programming Manual

Search results

Summary of Contents for CIX 200

Reviews:

Related manuals for CIX 200

Brands by name

Popular brands