Strata CIX 200 Programming Manual Download Page 175 | Manualshive

Page: 175 / 508

background image

System

Dial Number Plan

Strata CIX Programming Vol.1 12/09

4-15

System

105 System Data

Prerequisite Program:

None

This command assigns system settings for your Strata CIX.

1. In Network eManager, click System > System Data.

2. Enter System Parameter data using the table below.

3.

Get

Default

sets all values to factory default.

4. Click

Submit

.

F

IELD

D

ESCRIPTION

01 Executive Override

Enable break in warning tone for Executive Override.

Possible values:Enable (default) or Disable

02 Station MOH Source

Music On Hold selection for private lines, Tie lines and stations.

Refer to PRG109 for equipment MOH assignments.

Possible values:Quiet Tone, External 1 ~ 15, Internal (default)

03 Ring Transfer Tone

Determines whether a call hears RBT or MOH while being transferred and
prior to the destination party answering.

Possible values:RBT (default) or MOH

04 Transfer Privacy

Transfer Privacy enabled: CO line buttons that have multiple appearances
will only flash and ring on the transferred-to telephone; the same CO line
button on other telephones will be red-busy.

Transfer Privacy Disabled: CO line buttons that have multiple appearances
will flash and ring on all telephones having the CO line button appearance.

Possible values:Enable (default) or Disable

05 Privacy Override

Enables warning tone to members of a call prior to that call’s being subject
to Privacy Override or Attendant Monitor.

Possible values:Enable or Disable (default)

06 Credit Card Code

Enter Service Indentifier for Credit Card Calling. If no value is entered in this
field any previously programmed data is lost.

Possible values:Up to 32 digits (default = no value)

07 Credit Card Digits

Minimum Dial Digits required for Credit Card Calling. This should be the
quantity of digits in a credit card number. If this quantity of digits is not
dialed when making credit card calls, the caller will be disconnected. This is
to ensure that the call is charged to a credit card. DRL tables in Program
111 and OLGs in Program 306 must be enabled with credit card calling for
this feature to be active. Users must be assigned to a DRL table enabled
with credit card calling and call out on a credit card calling enabled OLG for
this featured to be applied to the call.

Possible values:1~32 (default = 21)

08 E911 Service

Enable E911 Service availability.

Possible values:Enable (default) or Disable

«
...
173
174
175
176
177
...
»

Summary of Contents for CIX 200





























































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for CIX 200

Brand: Hama Pages: 12

Brand: Panasonic Pages: 4

Brand: Yealink Pages: 2

Brand: Sagem Pages: 72

Brand: Sagem Pages: 63

Brand: Sagem Pages: 77

Brand: Yealink Pages: 361

Brand: Yealink Pages: 7

Brand: Yealink Pages: 4

Brand: Yealink Pages: 2

Brand: Yealink Pages: 7

Brand: Alcatel Pages: 67

Brand: Yealink Pages: 143

RED ALERT 397-710CB

Brand: GAI-Tronics Pages: 24

Brand: Blackberry Pages: 28

Mini Mobile Phones

Brand: TTS Pages: 8

Brand: Akuvox Pages: 83

Brand: Sony Ericsson Pages: 75

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands