manualshive.com logo in svg

Strata CIX 200, Programming Manual

The "Strata CIX 200" General Description Manual is a comprehensive guide for users of this advanced telecommunication system. This manual provides in-depth information about its features, functions, and troubleshooting, enabling users to maximize the potential of their device. Download this manual for free from our website and become an expert user of Strata CIX 200. [Website]

Share
Download
background image

Data Backup and Restore

Local Update

Strata CIX Programming Vol.1    12/09

14-9

Da
ta

 Back

up and

 

Restore

Step 5: Confirm Software is Updated and Backup Data is Restored

1.

When the telephone LCDs display and system dial tone is available, try to log in to the Programming 
Mode from digital telephone. (If Update/Restore is finished, you can log in).

2.

From the programming telephone check the Strata CIX version number using Program 901.

3.

Turn the CIX100 power off for 5 seconds and then back on to reset QISG, ISDN and other advanced 
features.

4.

Test the system to verify that the new software is running properly by checking dial tone, making 
incoming and outgoing calls, internal and external calls and all other peripherals, such as voice mail, 
etc., are working correctly.

5.

Toshiba recommends that the SmartMedia card containing the customer data remains installed on the 
CIX processor. This enables you to make and back up changes using Network eManager remotely.

Important!

It is your responsibility to verify the system is working correctly after local Update is 
complete.

Strata CIX670 or CIX1200 Local Update

The Update process is used to change the Strata CIX software version and restore programmed data. The 
new software is first copied from the SmartMedia card to the standby side of the Strata CIX processor flash 
RAM. Then the new software on the Standby flash RAM is switched to the active mode and the original 
software is switched to the Standby mode for a trial run.

After swapping the software version making the new software “Active,” the Strata CIX restores the 
programmed data. If the system functions properly, the trial operation can be set to normal operation; if 
there are problems you can switch the original software back to Active.

A CIX default.dat database can only be restored to a CIX software version that is the same or higher than 
the CIX software version on which the default.dat file was created. 

Examples: 

•

A default.dat created on CIXR2.0 MF013 can be restored on an R2.0 MF013, MF014 and higher. 

•

R2.2 MF0XX, R2.1MG0XX (XX = 01~99), cannot be restored on R2.0 MF012, MF011 and lower, or 
R1.X ME0XX, MD0XX, etc.

Step 1: Prepare SmartMedia Card with a Backup of the Customer Database

This SmartMedia card will contain a Backup of the Strata CIX programmed data (default.dat).

1.

Insert a SmartMedia card into the CIX, format it, and then back up the customer database onto the 
SmartMedia card using the Backup Data procedure (see

 

“R3.0 and Earlier Data Backup” 

on 

page 14-4

).

This operation writes the default.dat file under the PROGDATA directory to the SmartMedia card.

2.

Remove the SmartMedia card from the CIX and physically label it “Strata CIX Backup data.”

Step 2: Prepare SmartMedia Card with a Copy of the New CIX Software

This SmartMedia card will contain the new Strata CIX software file (nhs.prg) used to Update the system 
software.

1.

Obtain the Strata CIX operating software file (nhs.prg) from Toshiba FYI and store it on an 
appropriately named folder on your PC – see

 

“Download and Extract CIX Software” 

on 

page 14-6

.

2.

Insert a SmartMedia card into Strata CIX processor SmartMedia socket and activate the Forced 
Format command using Program 908; then Unmount SmartMedia using Program 908.

Summary of Contents for CIX 200





























































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for CIX 200

Panasonic EB-3901 User Manual preview
EB-3901
Brand: Panasonic Pages: 83
Panasonic KX-UT123 Admin Manual preview
KX-UT123
Brand: Panasonic Pages: 5
Panasonic KX-UT123 Administrator'S Manual preview
KX-UT123
Brand: Panasonic Pages: 312
Panasonic Section 700 Technical Manual preview
Section 700
Brand: Panasonic Pages: 311
Yealink Yealink SIP-T22P Quick Reference Manual preview
Yealink SIP-T22P
Brand: Yealink Pages: 4
Yealink Yealink SIP-T22P Installation Manual preview
Yealink SIP-T22P
Brand: Yealink Pages: 2
Yealink W79P Quick Reference Manual preview
W79P
Brand: Yealink Pages: 12
Yealink W53 Series Setup Manual preview
W53 Series
Brand: Yealink Pages: 8
Yealink Yealink SIP-T21P User Manual preview
Yealink SIP-T21P
Brand: Yealink Pages: 144
Yealink Yealink SIP-T41P User Manual preview
Yealink SIP-T41P
Brand: Yealink Pages: 178
Netway 4.5 qHD User Manual preview
4.5 qHD
Brand: Netway Pages: 68
Sonim XP3400 ARMOR User Manual preview
XP3400 ARMOR
Brand: Sonim Pages: 66
Fisher-Rosemount HART 275 Product Manual preview
HART 275
Brand: Fisher-Rosemount Pages: 116
HTC Sensation 4G T-Mobile Start Manual preview
Sensation 4G T-Mobile
Brand: HTC Pages: 38
Plum Polka D110 Manual preview
Polka D110
Brand: Plum Pages: 24
AirTyme GTX75 User Manual preview
GTX75
Brand: AirTyme Pages: 159
AMGOO AM355 Manual preview
AM355
Brand: AMGOO Pages: 14
NEC 16LD ADM User Manual preview
16LD ADM
Brand: NEC Pages: 89

Brands by name

Popular brands

Load more brands