Strata CIX 200 Programming Manual Download Page 310 | Manualshive

Page: 310 / 508

background image

Trunks

Trunk DID/DNIS Setup Wizard

6-56

Strata CIX Programming Vol.1 12/09

329 SIP URI Assignment

Prerequisite Program:

100; 304; 309; 306; 326, 327, 328

The SIP URI is the telephone number provided by the SIP service provider. When the number is dialed
from the outside, the provider sends a SIP INVITE just as if it were a call to a SIP station.

1. Select IP-Telephony > SIP Trunking, URI tab.

2. Enter the information required as specified in the table below.

3. Click the action to perform:

Add, Modify,

or

Remove

.

F

IELD

D

ESCRIPTION

00 SIP URI Trunk Service
Index

The Prog 327 index for the service kind associated to this SIP URI.

Possible values:1~32 (CIX40), 1~32 (CIX100), 1~48 (CIX200/CIX/670 Basic/

CIX1200 Basic), 1~128 (CIX/670 Exp./CIX1200 Exp)

01 URI Index

The Index into the table of URIs There are a maximum of 160 per card.

Possible values:1~72 (CIX40), 1~72 (CIX100), 1~160 (CIX200/CIX/670 Basic/

CIX1200 Basic), 1~160 (CIX/670 Exp./CIX1200 Exp).

02 SIP URI

The user portion of the SIP URI. The host portion is assigned by Prog 327 field 5.

03 SIP URI User Name

The user name used for authentication of this URI.

04 SIP URI Password

The password used for authentication of this URI

05 SIP URI Channel

Group

0 (recommended) means the channel group is picked out from Prog 328.
Otherwise, this SIP URI is registered through the specifically set channel group.

06 SIP URI Attribution

MAIN specifies that this URI will be registered with the service provider. SUB
indicates that this URI will not be registered.

«
...
308
309
310
311
312
...
»

Summary of Contents for CIX 200





























































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for CIX 200

Brand: Garmin Pages: 20

Brand: Garmin Pages: 20

Brand: Garmin Pages: 32

Brand: Garmin Pages: 12

Garmin-Asus A10

Brand: Garmin Pages: 20

Brand: NTT docomo Pages: 68

Brand: Point Mobile Pages: 8

Brand: HART Pages: 22

Brand: Med-Pat Pages: 37

Brand: Zte Pages: 113

Mi Note 10 Lite

Brand: Xiaomi Pages: 101

6185 - Cell Phone - CDMA

Brand: Nokia Pages: 105

6233 - Cell Phone 6 MB

Brand: Nokia Pages: 123

Brand: Zte Pages: 34

Verizon Galaxy Note7

Brand: Samsung Pages: 2

Verizon Convoy 4

Brand: Samsung Pages: 2

UPROAR SPH-m100

Brand: Samsung Pages: 8

Brand: Samsung Pages: 32

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands