Strata CIX 200 Programming Manual Download Page 280

Page: 280 / 508

Trunks

ISDN

6-26

Strata CIX Programming Vol.1 12/09

ISDN

The following program enables set up for ISDN-related system settings.

317 ISDN BRI Trunk

Prerequisite Program:

100

page 4-1

This command assigns ISDN BRI Trunks.

1. Select > Trunk > ISDN BRI.

2. Enter Channel Group number or click one of the following buttons:

•

List

– choose from a list of programmed trunks on the right side of the screen.

•

Create

– Assign a new trunk with default settings.

•

Copy

– Enter a Channel Group number and click

Copy

to make a new trunk assignment with

settings copied from the Channel Group you entered.

•

Delete

– Delete a trunk.

•

Get Default

- restores data to factory defaults.

3. Enter data.

4. Click

Submit

IELD

ESCRIPTION

Channel Group

Enter the BRI channel Group Number.

Possible values:1~32 (CIX40), 1~32 (CTX100), 1~48 (CTX670 Basic & CIX200),

1~128 (CTX670 Exp), 1~48 (CIX1200 HCTU only), 1-128
(CIX1200 HCTU+HEXAU), 1~220 (CIX1200 HCTU +HEXBU)
(default = 0)

Summary of Contents for CIX 200





























































































































































































































































































































































































































































































































Search results

Summary of Contents for CIX 200

Reviews:

Related manuals for CIX 200

Brands by name

Popular brands

Strata CIX 200, Programming Manual

Search results

Summary of Contents for CIX 200

Reviews:

Related manuals for CIX 200

Brands by name

Popular brands